MB 1K S : Spraying-optimised, multi-functional...

Article No. 085225

MB 1K S

Single-component multi-functional building waterproofing material for machine application

Product variants

Variant table

Downloads & documents

Technical Data Sheet

Safety Data Sheet

Declaration of performance

➥Show all documents (in different languages) for download / dispatch

Brochures

product.brochures.loading

Product specifications

On delivery

Base Polymer binder, additives, special fillers

Crack-bridging ≥ 3 mm (at ≥ 3 mm dry layer thickness)

Layer thickness 1.3 mm wet layer thickness yields approx. 1 mm dry layer thickness

Cross-slit pressure tests Passed, even without reinforcement fabric inlay

Water vapour permeability 9680

Drying time Approx. 8 h at 2.5 mm wet layer thickness (20 °C/65% RH)

Density Approx. 1.05 kg/dm³

The stated values represent typical product characteristics and are not to be construed as binding product specifications.

Product details Application Usage / application examples Notes

Field of application

Waterproofing in new buildings
Can be applied > 3 m in the ground
Connection to water-impermeable concrete structures
Cross-sectional waterproofing in and under walls
Wall base and render waterproofing
Subsequent exterior waterproofing in existing buildings
Bonding layer on old bitumen coatings

Properties

Can be applied as a slurry, with a brush or by spraying
Rapid bond adhesion, even on non-mineral substrates
Very low emissions (GEV-EMICODE EC 1^Plus)
Highly flexible, elastic and crack-bridging
Radon-tight (verified through testing)
Water pressure tight
Can be plastered and painted over
Fast, crosslinker-assisted complete drying
Freeze/thaw-resistant

Preparation
Substrate requirements

The substrate must be clean, dry, flat and capable of bearing a load, and free of dust, oil, grease and release agents.

Roughen non-mineral and pore-free substrates.

Preparations

Remove projecting seams and mortar remains.

Break off or chamfer corners and edges.

Produce the sealing cove with a suitable mortar.

Seal off indentations > 5 mm using a suitable filling knife.

Roughen the surface of plastic pipes with sandpaper; clean and, if necessary, sand metal pipes.

If necessary, provide damp proofing.

Prime absorbent mineral substrates with Kiesol MB.

Create a scratch coat using the product as a contact layer and in order to prevent blisters.

Allow the scratch coat to dry completely.
Application
Vertical/horizontal surface waterproofing, and waterproofing in and under walls:

Apply the product in two layers on the previously prepared substrate.

Pipes passing through walls

W1-E: seal pipe penetrations by using the product to form a cove around them.

Wall base render

Cover with bonding and reinforcing mortar, e.g. Remmers VM Fill / VM Fill rapid, once completely dry.

Embed the reinforcing fabric into the render layer over the entire surface.

Coating

Direct coating with binder-rich dispersion coats.

Always set up a trial area/trial areas first.

Machine working

The 1000 kg containers (085261) are equipped with an IBC adapter with Storz coupling (C52) for direct material delivery.
Application instructions
In the case of liquid-applied waterproofing materials, direct sunlight and/or wind exposure can cause accelerated skin formation and accompanying blistering.

Do not use in direct sunlight.

The scratch layer does not as a rule count as a waterproofing layer.

Protect the fresh waterproofing layer from rain, direct sunlight, frost and condensation water.

Once dry, protect from mechanical damage.

Add a further load-distributing layer if using the product for waterproofing under raised floor supports.

Ensure sufficient ventilation when applying the product in closed areas (wear respiratory protection if necessary).

Please contact Remmers Technical Service (phone +49 5432 83900) before applying with machine processing.

The maximum wet layer thickness must not exceed 4 mm.

The formation/sealing of internal corners without a sealing cove has not been tested by the building authorities.

Type I joints, in which joint tapes made of plastic or elastomer membranes with fleece or fabric lamination are to be embedded in the waterproofing, can only be executed with two-component liquid-applied waterproofing materials (FPD/MWS).
Working tools / cleaning
Slurry brush, flat brush, roller

Suitable machine technology, such as peristaltic pumps, screw pumps or airless piston pumps

Clean tools with water while the material is still fresh.

Any material that has already begun to dry can only be removed mechanically.
Storage / shelf life
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 9 months.

Usage
Min. 1.3 kg/m²/mm dry layer thickness

Layer thickness and application rate for exterior use:
See application rate table under application examples.

Apply to a large enough trial area to determine the precise amount required.

Application examples

Water impact classes (DIN 18533 / 18535)		Dry layer thickness (mm)	Wet layer thickness (mm) ****	Application rate (kg/m²)	Yield 25 kg (m²)
W1-E*	Ground moisture and non-pressing water	≥ 2	approx. 2.6	approx. 2.7	approx. 9.25
W2.1-E**	Moderate impact of pressing water ≤ 3 m immersion depth	≥ 3	approx. 3.9	approx. 4.0	approx. 6.25
W2.1-E** Transition to components made from water-impermeable concrete	Moderate impact of pressing water ≤ 3 m immersion depth	≥ 4	approx. 5.3	approx. 5.5	approx. 4.5
W2.2-E***	High impact of pressing water > 3 m immersion depth	≥ 4	approx. 5.3	approx. 5.5	approx. 4.5
W4-E	Splashing water and ground moisture at the wall base, and capillary water in and under walls	≥ 2	approx. 2.6	approx. 2.7	approx. 9.25
W2-B	Water loads in tanks with fill level ≤ 10 m	≥ 3	approx. 3.9	approx. 4.0	approx. 6.25

* Special agreement required for use on masonry

** Special agreement required

*** Special agreement required - only permitted on concrete substrates up to 10 m immersion depth

**** The maximum total wet layer thickness must not be exceeded including when applied in two layers (wet on wet).

Layer thickness allowance as per DIN 18533:

The German standard prescribes a layer thickness allowance dz to ensure the minimum dry layer thickness dmin. This accounts for application-related fluctuations dv as well as the additional material needed to level out the substrate du. If the substrate is levelled separately (e.g. with a scratch coat), du is eliminated from the calculation.

du = scratch coat, application rate approx. 0.5 kg/m² (depending on the substrate)

dv = not required with layer thickness trowel / application rate without layer thickness trowel approx. 0.4 kg/m² (dmin = 3 mm)

General information
The characteristic data of the product were calculated under laboratory conditions at 20°C and 65% relative humidity.

Current regulations and legal requirements must be taken into account and deviations from these must be agreed separately.

The relevant test certificates must be observed when planning and carrying out work.

Special agreements and certificates of suitability can be downloaded online at www.remmers.com.

Always set up a trial area/trial areas first.

The material is UV-resistant on vertical surfaces in the wall base area and can also be used without a coat of paint/plaster applied in areas without ground contact.
A change in colour is possible, but has no impact on the waterproofing function.

Peel tests are neither suitable nor authorised for assessing the suitability of the product for use.
Disposal instructions
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
Safety / regulations
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.