• OB-008 Oil Stain

    Article No. 278701

    OB-008 Oil Stain

    Solvent-based linseed oil stain with a very long open time

    Colour: clear | 2787
    Colour: clear | 2787
    Please choose a colour
    Size / Quantity

    Product specifications

    On delivery

    Binder Linseed oil/natural resin
    Density (20°C) Approx. 0.82 g/m³

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors
    • for stairs
    • for wood floors
    • for interior doors
    • for furniture
    • For professional users only
    • Especially for use on softwoods and large-pored woods (e.g. oak)
    • For use under finishes on an oil, wax or alkydic resin base

    Properties

    • Solvent-based
    • Ready-for-use base colours that can be mixed with each other
    • Long open time for streak-free application (on large surfaces)
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood moisture content: 8-12%

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Wash off greasy or resin-rich woods/substrates with WV-891 or V-890. Use UN-894 indoors on the construction site. Ensure good ventilation for solvents.

        Sand wood with P 80 - 150.

        The coarser the sanded finish, the more intense the colouring in pigmented varieties will be.

    • Application
      • Application temperature: min. 18 °C max. 25 °C
      • Stir before use
      • By brush / By roller / Filling knife
      • Stir well.

        Application by roller, brush, spreader or pad.

        Remove any excess material using a lint-free cotton cloth after approximately 20-30 minutes.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Before coating technically modified woods and wood-based materials, apply the coating to a trial surface and conduct a suitability test on the desired area of use.

        Ensure good ventilation.

        Risk of self-ignition (DGUV information brochure 209-046).

        The product should not be applied at the same work stand as NC-based varnishes or stains. Collect any textiles soiled with the product (e.g. cleaning rags, work clothing) in fire-resistant waste containers and dispose of properly.

      • Drying

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

    • Working tools / cleaning
      • By brush / By roller / Filling knife
      • Flat brush, short-pile (3-5 mm) velour or mohair roller, rotary disc machine with white non-abrasive pad, wadded rag/lint-free cotton cloth, stainless steel/spring spatula.

        Clean tools immediately after use with V 101 Thinner.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 24 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

    • Usage
      • Approx. 40 ml - 80 ml / m² per layer applied
      • 40 - 80 ml/m²

        The application rate is highly dependent on the absorbency of the wood and the final sanded finish.
        After every application, remove excess material with a lint-free cotton cloth after approx. 20-30 minutes.

    • General information
      • Oil-based products contain natural ingredients. Under the influence of UV light, exclusion of light (dark yellowing), heat or individual changes in the wood, these can lead to a change in the surface. The surfaces therefore require special care. Please refer to the information sheet on general application instructions for oils and waxes. White, pastel and grey tones can lose their intensity within a short period of time. This happens depending on the type of wood used, substances contained in the wood, exposure to light and heat. If these changes are not desired, a stained and lightfast lacquered surface finish is recommended.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.