• 221330 Adolit Holzwurmfrei

    Article No. 221330

    Adolit Wood Worm Free

    Water-based wood preservative for infestation control with long-lasting results

    Colour: clear | 2213
    Colour: clear | 2213
    Please choose a colour
    Size / Quantity

    Brochures

    product.brochures.loading

    Safety instructions

    • Use biocides safely. Always read the label and product information before using!

    Product specifications

    On delivery

    Appearance/colour Chemical yellow tinge
    Density (20°C) Approx. 1.08 g/cm³
    Odour Weak, characteristic

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and wood not directly exposed to weather
    • For professional users only
    • Wood in interiors and in protected outside areas
    • Control of wood-destroying insects for wooden building elements such as roof trusses, wooden beams, floors, etc.
    • House borer and deathwatch beetle
    • Also with preventive action against fungi and insects

    Properties

    • Water-based
    • Ready to use
    • Good penetration characteristics
    • Prevention of emergence pursuant to DIN EN 370
    • No unpleasant odour
    • Test predicates: Ib = effective control of insects, Iv = preventive effect against insects, P = preventive effect against fungi (rot protection)
    • Does not attack plastics, glass, copper, iron or coatings on these materials
    • Preparation
      • Substrate requirements

        Determine the nature and extent of the infestation.

        In case of doubt, consult a structural engineer.

        Strip away infested wood down to the deepest feeding tunnels.

        If wooden building elements have suffered significant structural impairment, reinforce or replace them with timber that has been given preventive treatment.

      • Preparations

        Remove decomposed wood and loose wood fibres with a steel brush.

    • Application
      • Brush
      • Bore hole saturation
      • Pressure injection
      • Brush application, borehole impregnation under pressure, borehole impregnation

         

        Brush application:

        3 treatments are normally needed (wet-on-wet) to reach the required application quantity.

         

        Borehole impregnation:

        Taking the structural conditions into consideration, position the holes (diameter 10 mm, ¾ of the beam thickness) with a spacing of 10 cm offset from one another in the grain direction, and 5 cm across the grain.

        Drill vertical pieces of wood at an inclination of 35-45° facing downwards.

        Fill boreholes 3-4 times, then close up with an impregnated wooden dowel.

         

        Borehole impregnation under pressure:

        With injection under pressure, it is possible to apply the wood preservative in a single procedure. No inclination angle is required, so injection under pressure can also be used for overhead working. The borehole diameter is 5-10 mm. The wood preservative is injected at a pressure of 3-10 bar. In order to achieve the required application quantity, the injection pressure must be maintained for at least 30 s and the working pressure monitored, taking into consideration the absorption capacity and condition of the wood.

         

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 48 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        When using for infestation control in recreation rooms or adjoining rooms, use of the room as a recreation room is only permitted from 4 weeks after the treatment.

      • Drying

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

    • Working tools / cleaning
      • Brush
      • Bore hole saturation
      • Pressure injection
      • Flat brush, wide brush, funnel, injection pump, high-performance sprayer (e.g. Gloria 405/410 T), pressure hose with gripper head and bushing, plastic injector

        Clean tools immediately after use with water.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Store in well-sealed, original containers, out of the reach of children and in a dry, cool, well-ventilated room which is protected from direct sunlight and frost. No smoking is permitted in storage areas.

    • Usage
      • Total application/absorption rate 300 ml Total / m²
      • Infestation control: 300 ml/m²
        Preventive protection in the context of infestation control: 100 ml/m²

    • General information
      • The product has been evaluated according to the Biocidal products regulation (EU) No. 528/2012 and approved by the Federal Institute for Occupational Safety and Health (BAuA). This approval replaces the general approval by the German Institute for Building Technology (DIBt).

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

        European waste code 03 02 04* inorganic wood preservatives

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.