Aqua PF-430 Pigment & Sealing Filler

The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

Wood moisture content: 8-12%

Wash off greasy or resin-rich woods/substrates with WV-891 or V-890. Use UN-894 indoors on the construction site. Ensure good ventilation for solvents.

Softwoods: sand with P 80 - 120.

All other substrates: sand with P 180 - 320.

Stir well.

Spray.

Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.

Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.

Flow cup gun: nozzle 2.5 mm, atomizer air pressure: 2.0 - 3.0 bar.

Once dry, carry out intermediate sanding with P 240-320.

Repeat the process if necessary.

Intermediate and final coats of suitable products can be applied after drying.

Seal opened containers well and use contents as soon as possible.

Check colour, adhesion and compatibility with the substrate by setting up a trial area.

Before coating technically modified woods and wood-based materials, apply the product to a trial surface and conduct a suitability test on the desired area of use.

In damp room applications and on wood with a high concentration of active substances, the sealing effect can be significantly increased by adding Aqua VGA-485.

Mixtures with Aqua VGA-485 can mature/increase in viscosity within a few days.

For an optimum sealing effect, apply two coats of primer to wood types with high levels of active substances:

In some cases, wood types such as hevea, kambala/iroko, acacia should be sealed with Aqua AG-26.

Aqua AG-26 should be used for coatings that emphasise pores.

Dust-dry: after approx. 45 minutes
Can be overcoated: after approx. 2 hours
Can be stacked: after drying overnight
Final coat of PUR CL-24X: after drying overnight
Drying overnight improves the sealing effect

Practice values at +20 °C and 65% relative humidity.

Low temperatures, poor ventilation and high humidity delay drying.

Ready to use; if necessary dilute with max. 5% water.

Airless/airmix spraying equipment, flow cup gun

Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

120 - 150 ml/m² per coat

The indoor air cleaning effect has been independently tested and lasts for several years. The duration depends on the room conditions, air exchange rate, application quantity, formaldehyde concentration in the indoor air, and the wooden elements being coated. Applying a finishing coat over the product does not impair its effectiveness. The formaldehyde is irreversibly bound and no re-emission occurs. Dried varnish films do not differ from conventional coating materials in the following aspects: PPE during sanding, health risks of contact with the varnish, and disposal.

Relatively simple surfaces (e.g. inside faces of cabinets, stair components) can be coated with a clear topcoat such as Aqua TL-412 Stair Varnish directly after priming with Aqua PF-430 Pigment Filler.

The product can also be produced in light colours (based on RAL). Please note that the information given is approximate: RAL1013, RAL1014, RAL1015, RAL3015, RAL6019, RAL7035, RAL7038, RAL7044, RAL7047, RAL9001, RAL9002, RAL9010, RAL9016, RAL9018. Other colours are available upon request. For intensive full-tone colours, we recommend using Aqua VTF-435 Full Tone Filler.

Please refer to the relevant test reports/certificates and the Technical Data Sheet for information on certified products and configurations.

For applications in accordance with the Marine Equipment Directive, the maximum wet application quantity is 3 x 150 µm.

Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.