Induline GW-203 WF

The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).

Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

Stir well, including during application or after a break in work.

After drying, apply an intermediate coat of this product or a suitable finishing coat.

Ensure good ventilation.

Seal opened containers well and use contents as soon as possible.

Check colour, adhesion and compatibility with the substrate by setting up a trial area.

Before coating technically modified woods and wood-based materials, apply the coating to a trial surface and conduct a suitability test on the desired area of use.

For the best possible insulation from soluble substances in wood (surface and knots) the higher values for number of coats, application rates and drying times must be observed.
Coating with this product may activate the substances contained in the wood and discolour the paint layer. In this case these substances are fixated inside the paint layer.
The follow-up coating should ideally be carried out using a product that supports the insulating properties of this product. This will usually prevent further impairment of this top coat by the substances in the wood.
Should discolouration continue to occur despite this advice being followed, we recommend consulting Remmers Technical Service.
Bleeding resin is a natural phenomenon and cannot be prevented by coating measures, see BFS Code of Practice No. 18.
Dilution of the product, excessive wood moisture, or failure to comply with the recommended coating sequence, application rates and drying times can have a significant negative impact on the insulating effect of the product.
Intermediate sanding should go no further than smoothing the wood fibres – the primer must never be sanded away.
With water-based coating systems there is always a residual risk of bleeding of substances contained in the wood!

If foaming occurs during the application process, we recommend adding 0.1-0.2% VP 9325 de-foaming agent strength 2 (3231).

Dust-dry: after approx. 1 hour
Can be sanded and overcoated: after approx. 4 hours
(at 23 °C and 50% RH)

If forced drying is used, can be sanded and overcoated: after approx. 20 minutes flash-off zone (at approx. 20 °C and 65 - 75% RH) / 75 minutes drying phase (approx. 45 °C, 1 m/s air circulation) / 20 minutes cooling phase

Low temperatures, poor ventilation and high humidity delay drying.

Ready to use

Vacuum equipment, acrylic brush, dipping tank, flow coating facility, spray applicator

Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

Ensure that any residue from cleaning is disposed of correctly.

If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

120 - 145 g/m² per coat
(corresponds to wet film thickness: 100 - 125 µm, dry coat thickness: 30 - 40 µm)
These values are based on sanded/planed surfaces; the application quantities may be significantly higher on rough surfaces (rough-sawn, fine-sawn etc.).

On planed larch and softwoods with a high resin content, the coating may have reduced adhesion and resistance to weathering. This is especially the case on horizontal year rings, knots and areas of winter growth that are high in resin. Maintenance and renovation must be carried out more frequently on these surfaces.
The only remedy for this is pre-weathering or very coarse sanding (P80).
If these wood types are rough-sawn, considerably longer maintenance and renovation intervals are to be expected.

Observe the information sheets “Upkeep and Maintenance of Dipping Tanks and Flow Coating Facilities” and “Information on Workplace Hygiene”.

Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.