©

External waterproofing

Effective protection against external effects of water

Reliability, fast and easy processes along with short waiting times are the most importanat aspects that a modern waterproofing system has to fulfill. Lots of professionals want to complete the waterproofing work in one day and continue working the next day. Remmers waterproofing systems perfectly meet these requirements.

©

Waterproofing below ground level (W1-E / W2-E)

The new version of the standard now approves crack-bridging mineral waterproofing mortars MWGS's for waterproofing concrete surfaces for water ingress class W1-E. For this application, MB 2K+ can be applied in compliance with the standard pursuant to PG MWG.

Since MB 2K+ not only meets the guidelines for crack-bridging MWG, but testing has prooved that the product also meets the properties of the PMBCs. This flexible, polymer-modified coating also covers areas of application outside the standard. With a specification, the material can now be used as waterproofing against water ingress class W1-E and W2-E regardless of the substrate.

Proof:

  • AbP pursuant PG MDS
  • AbP pursuant PG ÜBB
  • Satisfies the test requirement for PMBC (DIN EN 15814)

External waterproofing below ground with Remmers System Guarantee

Reliability, fast and easy processes along with short waiting times are the most importanat aspects that a modern waterproofing system has to fulfill. Lots of professionals want to complete the waterproofing work in one day and continue working the next day. Remmers waterproofing systems perfectly meet these requirements. In combination with the Remmers System Guarantee (RSG), we not only offer the best possible product system for below ground waterproofing , but also twice the reliability. For correct installation in the RSG system, certified RSG companies only need to provide the statutory stipulated adhesion of 5 years (BGB contract) and/or 4 years (VOB/B contract). The extended guarantee for a total of 10 years will be assumed to 100% by Remmers. The greatest advantage for the processing specialist company: The 10-year system guarantee has an exclusive advantage for the installer.

1 Preparation

Round off the edges of the projecting part of the foundation. Remove any compenents that reduce adhesion.

2 Levelling

Smooth unevenness and flaws > 5 mm with WP DS Levell. Pre-wet heavily absorbent subsurfaces with water.

3 Priming

Apply Kiesol (1:1 with water) evenly. Pre-wet heavily absorbent substrates with water. Leave out uneven areas.

4 Waterpoofing layer

Apply a layer of WP DC [basic] evenly with a mortar or wide brush.

©

5 Sealing cove

Apply the sealing cove of WP DS Levell into the fresh waterproofing protection and use a sealing cove trowel to create a profile with a radius of 50 mm.

6 Priming

Apply Kiesol (1:1 with water) evenly. Pre-wet heavily absorbent substrates with water. Leave out uneven areas.

7 Scratch coat

Apply the scratch coat of MB 2K+.

8 First waterproofing layer

Apply the first waterproofing layer of MB 2K+.

9 Second waterproofing layer

Apply the second waterproofing layer made of MB 2K+ as soon as the first coat is dry.

10 Insulation

After sufficient drying time, adhere the insulation completely with MB 2K+ or 2K inhibitors PMBCs.

11 DS Protect

Installation of the DS Protect up to the ground level.

The most economical solution for concrete basements

MB 2K+ is unique thanks to its multi-functionality and system efficiency. This is mainly due to the rapid and weather-independent drying of the material and the associated shorter construction times, and also the relatively low material consumption. A dry layer of 3 mm without a fabric insert is enough to waterproof even those parts that have contact with the ground standing in ground water. Compared to conventional systems where a layer thickness of 4 mm is required; this saves on material and omits any steps for embedding reinforcement fabric. Spray applying MB 2K+ is especially effective.

1 Preparation

Round off the edges of the projecting part of the foundation. Remove any compenents that reduce adhesion.

2 Levelling

Smooth unevenness and flaws > 5 mm with WP DS Levell. Pre-wet heavily absorbent surfaces with water.

3 Priming

Apply Kiesol MB evenly. Pre-wet heavily absorbent substrates with water. Leave out uneven
areas.

4 Scratch coat

Apply the scratch coat of MB 2K+.

©

5 Install joint band

Apply MB 2K+ near the inside corner and embed the joint band VF using a wet-in-wet method.

6 First waterproofing layer

Apply the first waterproofing layer of MB 2K+ evenly.

7 Second waterproofing layer

Apply the second waterproofing layer made of MB 2K+ as soon as the first coat is dry.

8 Insulation

After sufficient drying time, adhere the insulation completely with MB 2K+ or 2K inhibitors PMBCs.

9 DS Protect

Installation of the DS Protect up to the ground level.

High-quality cellar waterproofing with PMBC

Since the introduction of the new water proofing standard in July 2017, polymer modified, bituminous thick coating (PMBCs) like Remmers PBD 1K / 2K, can also be used as a water proofing against outside water pressure (W2.1-E). Until now this was only possible outside the standard if there is a special agreement. In contrast, the product requirements for PMBCs have not changed and are also defined by the harmonised substance norm DIN EN 15814 throughout Europe. Products that are used as transitions to WU concrete structures also require a ‘test certificate from the construction supervising authority for the general transition to WU concrete constructions’ (AbP) pursuant to PG-ÜBB in addition to the European specifications (CE symbol). PMBCs are generally applied with a trowel. Alternatively, the material can also be applied with system-compatible machine technology. Regardless of the application procedure, ensure that the dry layers comply with the current water proofing norm.

1 Preliminary work

Chamfer the edge of the projected foundation. Remove the adhesion-inhibiting components.

2 Equalisation

Close unevenness and flaws > 5 mm with WP DS Levell. Pre-wet heavily absorbent subsurfaces with water.

3 Priming

Apply Kiesol (1:1 with water) evenly. Pre-wet heavily absorbent subsurfaces with water. Leave out equalised areas.

4 Protection against underlying moisture

Apply protection against underlying moisture made of WP DC [basic] using a wide brush.

©

5 Sealing cove

Apply the sealing cove made of WP DS Levell into the fresh underlying moisture protection and use a sealing cover trowel to create a profile with a radius of 50 mm.

6 Priming

Apply Kiesol (1:1 with water) evenly. Pre-wet heavily absorbent subsurfaces with water. Leave out equalised areas.

7 Scratch coat

Apply the scratch coat made of PBD 2K.

8 First water proofing layer

Apply the first water proofing layer made of PBD 2K evenly.

9 Second water proofing layer

Apply the second water proofing layer made of PBD 2K as soon as the first coat can no longer be
damaged.

10 Heat insulation

After an adequate drying period, adhere the heat insulation completely with PBD 2K.

11 DS Protect

Assembly of the DS Protect up to the ground level.

External waterproofing

16 products found
 

View:

Article No. 300801

Special primer

Article No. 301408

Multi-functional building waterproofing Combines the properties of flexible and crack-bridging mineral waterproofing slurries (MDS) and bitumen thick coatings (PMBC)

Article No. 2088830

High-grade, crack-bridging, polymer-modified 2K bituminous thick coating with polystyrene

Article No. 507101

High-quality, premium sealing tape based on nitrile rubber and coated with non-woven fabric

Article No. 500301

Highly elastic, self-adhesive butyl rubber waterproofing tape on polypropylene non-woven fabric

Article No. 082301

Highly durable, 3-layer protective sheet with decoupling function

Article No. 040525

Rigid mineral waterproofing slurry for new buildings

Article No. 042625

Waterproofing filler with high sulphate resistance

Article No. 042325

Quick-setting waterproofing filler

Article No. 300501

Liquid retarder

Article No. 081501

3-layer protective system made of recycled PET

Article No. 081601

Holder for DS Protect [basic] and DS Protect AL