• Aqua 2HL-411/90-2K High Gloss Varnish

    Article No. 387205

    Aqua 2HL-411/90-2K High Gloss Varnish

    Light-fast, two-component topcoat for high-gloss varnishes

    Colour: clear | 3872
    Size / Quantity

    Product specifications

    On delivery

    Density (20°C) Approx. 1.03 g/cm³
    Runout time s in DIN 4 cup Approx. 20-22 s

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors
    • for interior doors
    • for furniture
    • For professional users only
    • Interior wood
    • Hardwood veneers
    • Finishing coat
    • High-quality furniture
    • Furniture and interior finishing work

    Properties

    • Water-based
    • Good flow properties
    • Quick-drying
    • Can be polished once cured
    • Efficient coating system thanks to high filling power
    • Minimal sinkage of the varnish film
    • High-gloss surfaces
    • Lightfast
    • Excellent resistance to chemicals
    • Good resistance to a wide range of commercially available hand creams
    • Fire resistant
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood moisture content: 8-12%

      • Preparations

        Wash off greasy or resin-rich woods/substrates with WV-891 or V-890.

        Sand using a sandpaper grit of P150-180.

        If colouring is desired, stain the substrate using Aqua KB-004, Aqua BB-007 or Aqua PB-006.

        Coloured, opaque high-gloss systems:
        Aqua CL-440 with Aqua VGA-485 on a suitable substrate

        Transparent high-gloss systems on large-pored woods:
        closed-pore priming with Aqua 2DS-450/50

        Transparent high-gloss systems on fine-pored woods:
        closed-pore priming with Aqua 2HL-411/90

    • Application
      • Application temperature: min. 18 °C max. 25 °C
      • Flow cup gun
      • Application requirements

        Temperature of the material, air and substrate: from min. +18 °C to max. +25 °C.

      • Spray.

        Flow cup gun: nozzle size: 1.6 - 1.8 mm; atomiser air pressure: 2 - 3 bar.

        If necessary, apply a second coat of the product after drying and intermediate sanding (P 320 - 600).

        Seal opened containers well and use contents as soon as possible.

        Mixed material residues must not be allowed to cure in closed containers.

    • Application instructions
      • Drying time: can be worked over after 12 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        When coating surfaces finished with a coloured varnish, a maximum of 5% of the coloured varnish can be added to the product if necessary. In such cases, it is essential to check the colour.

      • Drying

        Dust-dry: after approx. 30-45 minutes Touch-dry: after approx. 90 minutes Can be overcoated: after approx. 12 hours Can be polished: after approx. 3 days

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Ready to use; if necessary dilute with max. 10% water and/or add max. 3% V-490 as a retarding agent.

    • Working tools / cleaning
      • Flow cup gun
      • Flow cup gun

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 6 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 6 months.

    • Usage
      • Approx. 80 ml - 120 ml / m² per layer applied
      • 80-120 ml/m² per coat

    • General information
      • To preserve the quality of the surface, we recommend regular cleaning and care using a lint-free cotton cloth. Please use solvent-free and silicone-free cleaning agents.

        Please refer to the relevant test reports/certificates and the Technical Data Sheet for information on certified products and configurations.

        Before coating technically modified woods and wood-based materials, apply the coating to a trial surface and conduct a suitability test on the desired area of use.

        This product cannot be used for wet-on-wet coatings (as are common in solvent-based high-gloss varnishing systems).

        Coated horizontal surfaces should only be turned for further processing steps after approx. 12 hours of drying time (in order to prevent foaming).

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.