Article No. 550501
Light-fast 2K colour varnish for highly durable coatings
Product specifications
On delivery
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- Wood and wood-based materials
- High-quality furniture and fittings
- Exclusive interior fixtures, kitchen and bathroom furniture
- Especially suitable for use on surfaces that have been pre-treated with Remmers Aqua fillers
Properties
- Can also be used on vertical surfaces
- Good flow properties
- Good hiding power
- Very high resistance to metal rings
- Excellent resistance to chemicals
- Good resistance to a wide range of commercially available hand creams
- Lightfast
- Does not become glossy
-
Preparation
-
Substrate requirements
The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.
Wood moisture content: 8-12%
-
Preparations
Wash off greasy or resin-rich woods/substrates with WV-891 or V-890. Use UN-894 indoors on the construction site. Ensure good ventilation for solvents.
Thoroughly sand any old coatings that are still intact.
Sand wood using P 100 - 180 grit.
Sand panels using P 180 - 320 grit.
Sand filler using P 240 - 320 grit.
-
-
Application
-
Stir well.
Spray.
Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.
Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.
Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.
Carry out intermediate sanding (P 240 - 320) before subsequent coats.
Seal opened containers well and use contents as soon as possible.
-
-
Application instructions
-
Check colour, adhesion and compatibility with the substrate by setting up a trial area.
Before coating technically modified woods and wood-based materials, apply the product to a trial surface and conduct a suitability test on the desired area of use.
Prior to full application, please apply a test coat to a sample area under practical conditions using the desired system, then test or examine the surface properties.
To ensure optimum resistance to metal rings and to improve the resistance to chemicals, we recommend coating with a suitable, light-fast clear varnish.
For optimum durability of the finished surface, a room temperature of at least 20 °C should be maintained during the drying and curing phase (>48 hours).
Substrate-specific coating recommendations can be obtained using the system finder on our website www.remmers.com.
-
Drying
Practice values at +20 °C and 65% relative humidity.
Low temperatures, poor ventilation and high humidity delay drying.
-
-
Working tools / cleaning
-
Airless or airmix spraying equipment
Clean tools with cold water or Aqua RK-898 Cleaning Concentrate immediately after use.
Ensure that any residue from cleaning is disposed of correctly.
-
-
Storage / shelf life
-
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.
-
-
Usage
-
120 - 150 ml/m² per coat
-
-
General information
-
To preserve the quality of the surface, we recommend regular cleaning and care using a lint-free cotton cloth. Please use solvent-free and silicone-free cleaning agents.
-
-
Disposal instructions
-
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
-
-
Safety / regulations
-
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.
-
