Article No. 380201
Fire-resistant, light-fast, durable 1K colour varnish
Downloads & documents
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- Wood and wood-based materials
- High-quality furniture
- Interior finishing work: e.g. panels, borders, cladding & interior doors
- Shop fitting and trade fair stands
- Especially suitable for use on surfaces that have been pre-treated with Remmers Aqua fillers
- As a glass lacquer (in combination with Aqua VGA-485)
- Single-component: simple and economical handling
- Can also be used on vertical surfaces
- Good flow properties
- Good hiding power
- Short time until ready for stacking
- Good resistance to chemicals
- Good resistance to a wide range of commercially available hand creams
- Fire resistant
- 2K-ready: further improvement of the resistance to chemicals and scratches, as well as adhesion to glass, by adding 2% Aqua VGA-485 (isocyanate-free)
The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.
Wood moisture content: 8-12%
Wash off greasy or resin-rich woods/substrates with WV-891 or V-890.
Clean glass using V-890 or UN-894.
Thoroughly sand any old coatings that are still intact.
Sand wood using P 100 - 180 grit.
Sand panels using P 180 - 320 grit.
Sand filler using P 240 - 320 grit.
Apply by roller or brush (only when diluted).
Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.
Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.
Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.
Carry out intermediate sanding (P 240 - 320) before subsequent coats.
Seal opened containers well and use contents as soon as possible.
Check colour, adhesion and compatibility with the substrate by setting up a trial area.
Before coating technically modified woods and wood-based materials, apply the coating to a trial surface and conduct a suitability test on the desired area of use.
On non-wood substrates such as glass, sanded priming films, melamine resins and PU paints, adhesion can be significantly improved by adding Aqua VGA-485. Owing to the large number of possible material variants, careful checking must be carried out prior to application.
To ensure optimum resistance to metal rings and to improve the resistance to chemicals, we recommend coating with a suitable, light-fast clear varnish.
For a transparent coating over surfaces coated with a coloured varnish, we recommend adding 5-10% Aqua Colour Varnish in the desired colour to the clear varnish.
Dust-dry: after approx. 1 hour Overcoating: after approx. 4 hours
Practice values at +20 °C and 65% relative humidity.
Low temperatures, poor ventilation and high humidity delay drying.
Ready to use; if necessary, dilute with max. 5% water and/or use max. 3% V-490 as a retarding agent.
Working tools / cleaning
Airless/Airmix spraying equipment, flow cup gun, acrylic brush, foam roller
Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.
Ensure that any residue from cleaning is disposed of correctly.
Storage / shelf life
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.
120 - 150 ml/m² per coat
Please refer to the relevant test reports/certificates and the Technical Data Sheet for information on certified products and configurations.
To preserve the quality of the surface, we recommend regular cleaning and care using a lint-free cotton cloth. Please use solvent-free and silicone-free cleaning agents.
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
Safety / regulations
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.