• OB-008 Oil Stain

    Article No. 278701

    OB-008 Oil Stain

    Solvent-based linseed oil stain with a very long open time

    Colour: clear | 2787
    Colour: clear | 2787
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Binder Linseed oil/natural resin
    Density (20°C) Approx. 0.82 g/m³

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors
    • for stairs
    • for wood floors
    • for interior doors
    • for furniture
    • For professional users only
    • Interior wood
    • Especially for use on softwoods and large-pored woods (e.g. oak)
    • Wooden floors and stairs
    • Furniture and interior finishing work
    • For use under finishes on an oil, wax or alkydic resin base
    • Alone: as impregnation/tinting oil on surfaces with low loading

    Properties

    • Solvent-based
    • Ready-for-use base colours that can be mixed with each other
    • Long open time for streak-free application (on large surfaces)
    • Intense colour
    • Made from renewable raw materials (linseed oil and natural resin)
    • Cobalt-free and MEKO-free
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood moisture content: 8-12%

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Wash off greasy or resin-rich woods/substrates with WV-891 or V-890.

        Sand wood with P 80 - 150.

        The coarser the sanded finish, the more intense the colouring in pigmented varieties will be.

    • Application
      • Stir before use
      • By brush / By roller / Filling knife
      • Application temperature: min. 18 °C max. 25 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +18°C to max. +25°C.

      • Stir well.

        Application by roller, brush, spreader or pad.

        When applying each coat, remove any excess oil using a lint-free cotton cloth after approximately 20-30 minutes.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Ensure good ventilation.

        Risk of self-ignition (DGUV information brochure 209-046).

        The product should not be applied at the same work stand as NC-based varnishes or stains. Collect any textiles soiled with the product (e.g. cleaning rags, work clothing) in fire-resistant waste containers and dispose of properly.

      • Drying

        Dust-dry: after approx. 4 hours Overcoating by spraying: after approx. 6 hours Overcoating with a roller: after approx. 14 hours

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        If necessary, dilute with max. 2% Thinner V 101. OB-008 Oil Stain (clear) is the base material for thinning and for adjusting/reducing the colour intensity.

    • Working tools / cleaning
      • By brush / By roller / Filling knife
      • Flat brush, short-file (3-5 mm) velour or mohair roller, rotary disc machine with white non-abrasive pad, rags/lint-free cotton cloth, stainless steel/spring spatula

      • Clean tools immediately after use with V 101 Thinner.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Shelf-life 24 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

    • Usage
      • Approx. 40 ml - 80 ml / m² per layer applied
      • 40 - 80 ml/m² The application rate is highly dependent on the absorbency of the wood and the final sanded finish. After every application, remove excess material with a lint-free cotton cloth after approx. 20-30 minutes.

    • General information
      • Owing to the need to remove excess material, limits are placed on the colour intensity (e.g. very dark colours and white). For optimum colour intensity, max. 5% of this product can be added to the seal coat.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.