• Adolit Holzbau B
  • Adolit Holzbau B
    • Adolit Holzbau B
    • Adolit Holzbau B

    Article No. 211103

    Adolit Holzbau B

    Water-based wood preservative; free of heavy metals and ready to use

    Colour: clear | 2111
    Colour: clear | 2111
    Please choose a colour
    Size / Quantity

    Brochures

    product.brochures.loading

    Safety instructions

    • Use biocides safely. Always read the label and product information before using!

    Product specifications

    On delivery

    Density (20°C) Approx. 1.1 g/cm³
    Odour Odourless

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and wood not directly exposed to weather
    • For structural elements
    • For professional users only
    • Wood in interiors and in protected outside areas
    • Wood without ground contact as per DIN EN 335-1, use classes 1 and 2
    • Building elements subjected to high static loads
    • Wood not subject to static loads
    • Suitable for solid structural timber (KVH)

    Properties

    • Water-based
    • Ready to use
    • Good penetration characteristics
    • Preventive protection against wood-destroying insects and fungi
    • Does not attack plastics, glass, copper, iron or coatings on these materials
    • Odourless
    • Preparation
      • Substrate requirements

        The substrate must be clean and free of dust.

        Permissible wood moisture content: > 20% (artificially dried construction timber excluded).

        The wood should have already been cut to measure.

      • Preparations

        Completely remove old coatings (e.g. paints or medium-build stains), bark, bast and dirt.

        If necessary, use a sprayer and water to moisten dry wood (u <20%).

    • Application
      • Brush
      • Bore hole saturation
      • Pressure injection
      • Application temperature: min. 5 °C
      • Application requirements

        Temperature of the material, air and substrate: from +5 °C

      • Brush application, borehole impregnation under pressure, borehole impregnation

        Once dry (waiting time min. 4 weeks), the treated wood can be further treated with approved solvent-based or water-based coatings.

        To enable the wood to dry and prevent the wood preservative from washing off, store in a covered area on sturdy, non-permeable ground.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 48 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

      • Drying

        Dry: after min. 48 hours Overcoating: after min. 4 weeks

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

    • Working tools / cleaning
      • Brush
      • Bore hole saturation
      • Pressure injection
      • Flat brush, wide brush, funnel, injection pump, high-performance sprayer (e.g Gloria 405/410 T), pressure hose with gripper head and bushing, plastic injector

      • Clean tools immediately after use with water.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Store in well-sealed, original containers, out of the reach of children and in a dry, cool, well-ventilated room which is protected from direct sunlight and frost. No smoking is permitted in storage areas.

    • Usage
      • Total salt concentrate application rate 120 ml Total / m²
      • Preventive action against rot and insects at 120 ml/m² (= 132 g/m²)

    • General information
      • The product has been evaluated according to the Biocidal products regulation (EU) No. 528/2012 and approved by the Federal Institute for Occupational Safety and Health (BAuA). This approval replaces the general approval by the German Institute for Building Technology (DIBt).

        In accordance with DIN 68800-1, wood preservation measures must be planned in a timely and careful manner in coordination with all parties involved in the construction (architect, client, contractor) taking into account legal requirements and local conditions.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

        European waste code 03 02 04* inorganic wood preservatives

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.