• Garden Wood Oils [eco]

    Article No. 769001

    Garden Wood Oils [eco]

    Water-emulsified oil made from renewable materials for wood terraces and garden furniture

    Colour: Bangkirai Oil [eco] | 7690
    Colour: Bangkirai Oil [eco] | 7690
    Please choose a colour
    Size / Quantity

    Product specifications

    On delivery

    Binder Based on plant oils
    Density (20°C) Approx. 1.02 g/cm³
    Odour Mild
    Degree of gloss Matt

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • for wood garden furniture
    • Pigmented variants: interior and exterior wood
      Clear variant: interior wood & wood in sheltered outdoor areas
    • (Garden) furniture and wooden decking
    • Wood types including teak, bangkirai, larch, Douglas fir and Accoya
    • Building elements with no or limited dimensional stability
    • Wooden beehives, bee boxes and other wooden elements used in beekeeping
    • Not suitable for massaranduba or tabebuia: we recommend the use of Remmers Maintenance Oil for these species of wood
    • Please get in touch with the Remmers Technical Service team before using on other, exotic species of wood not named here
    • We recommend the use of WPC Impregnation Oil on WPC, bamboo and Resysta


    • Water-based
    • Made from at least 80% renewable raw materials
    • Bee-friendly formula
    • A vegan product based on the information available to us
    • Water-based with a very low solvent content
    • Slip-resistant
    • Weather-resistant and UV-resistant
    • Preparation
      • Substrate requirements

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Wood which is rich in active substances should be weathered for a few weeks or cleaned with Wood Cleaner before being treated for the first time in order to prevent delays in the drying process.

        In order to prevent considerable delays in the drying process (up to 1 week), surfaces which have been treated with the conventional Remmers Garden Wood Oils (bangkirai oil (2632), Douglas fir oil (2633), larch oil (2634), teak oil (2635) and universal oil (2636)), can only be reworked using this product at the earliest after 6 months. Please apply these product varieties unmixed.

        Use an agent such as Wood Cleaner to remove any dirt, grease and old coatings that could form a film, making sure not to leave any residue.

        Clean any greyed wood surfaces with Wood Revitalizer.

        Remove algae with Green Growth Remover*. (*Use biocides safely. Always read the label and product information before use.)

        Wood building elements should be constructed so they shed and do not retain water (avoid level surfaces, open end-grain wood, capillary joints, water and moisture accumulation points, contact with splash water, sharp edges), thereby reducing the need to use wood preservatives as far as possible.

        Pre-treat exterior wood which requires protection against rot and blue stain with Wood Protection Primer.* (*Use biocides safely. Always read the label and product information before use.)

    • Application
      • Brush
      • Stir before use
      • Application temperature: min. 5 °C max. 25 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +25 °C

      • Stir well.

        Apply by brush.

        Treat all sides (of decking) on the first coat if possible.

        Apply the product using an acrylic brush or surface brush in the direction of the grain.

        Remove or smooth out any excess material (especially in tongues and grooves) immediately.

        Apply a further coat if required.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Although the various colours are matched to a specific type of wood, they can easily be used on other types of wood as well, in which case the look of the colour will differ from the corresponding sample.

        The clear variant does not protect against UV radiation (greying) and should therefore be used only on wood elements not directly exposed to weather (i.e. protected against direct sunlight, precipitation and wind). If a clear coating is desired on a directly exposed exterior surface, apply several coats and refresh at regular intervals.

        Rainfall may cause water soluble substances to bleed from wood that is rich in such substances, e.g. oak, red cedar, afzelia, redwood, etc. This may lead to the discolouration of light-coloured masonry or render.

        Cut end-grain surfaces at the bottom to create a water-drip edge.

        Apply two subsequent coats of end-grain wood preservative to end-grain wood and cut surfaces in order to protect them against moisture.

        Regular reapplications are required in areas exposed to weathering.

      • Drying

        Overcoating: after approx. 4 hours

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

        Drying may take longer depending on the type of wood, e.g. oak, due to substances it contains.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • Brush
      • Acrylic brush, flat brush (synthetic bristles)

      • Clean tools immediately after use with water and detergent.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

    • Usage
      • Approx. 60 ml / m² per layer applied
      • Approx. 60 ml/m² per coat Higher application rate on rough and grooved wood. Application quantity depends on the absorbency of the substrate. Determine the precise quantity by applying to a test area. Max. 2 coats, apply thinly by brush. Remove or smooth over any excess material immediately (especially in notches and grooves).

    • General information
      • Brush surfaces thoroughly and do not use any high-pressure water jet equipment or aggressive cleaning agents.

        Please observe the “Care Instructions for Wooden Garden Furniture”.

        On planed larch and softwoods with a high resin content, the coating may have reduced adhesion and resistance to weathering. This is especially the case on horizontal year rings, knots and areas of winter growth that are high in resin. Maintenance and renovation must be carried out more frequently on these surfaces. The only remedy for this is pre-weathering or very coarse sanding (P80). If these wood types are rough-sawn, considerably longer maintenance and renovation intervals are to be expected.

        On terrace surfaces in the area of swimming pools, the increased exposure to chlorine, cleaning agents and intensive moisture can lead to reduced adhesion and weathering of the coating. Shorter maintenance and renovation intervals must be expected here.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.