• End Grain Sealer

    Article No. 190001

    End Grain Sealer

    Moisture protection for cut surfaces

    Colour: clear | 1900
    Size / Quantity

    Product specifications

    On delivery

    Binder Acrylate
    Density (20°C) Approx. 1.04 g/cm³
    Odour Mild, odourless once dry

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For use on interior and exterior wood
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking
    • Soft and hard woods
    • Moisture protection for cut surfaces and end-grain wood

    Properties

    • Water-based
    • Film-forming
    • Repels water
    • Elastic
    • Inhibits diffusion
    • Effective restriction of volume increase due to moisture in the treated wood
    • Can be overcoated with conventional coating systems
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).

        Products that do not form films (low-build stains and oils) must be fully applied before this product is used, otherwise they will not be able to penetrate the substrate.

        This product must be applied between the first and second coat of products that do form films (medium-build stains and topcoats).

        After priming, carry out light intermediate sanding.

    • Application
      • Application temperature: min. 5 °C max. 25 °C
      • Stir before use
      • Brush
      • Stir well.

        Apply by brush.

        A repeat application may be required in exceptional cases.

        Intermediate and final coats of suitable products can be applied after drying.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 2 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Before coating technically modified woods and wood-based materials, apply the product to a trial surface and conduct a suitability test on the desired area of use.

        Ensure good ventilation.

      • Drying

        Can be overcoated: after approx. 2 hours

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • Brush
      • Brush with synthetic bristles, flat brush

         

        Clean tools immediately after use with water and detergent.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 24 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

        Use the contents of open containers as quickly as possible.

    • Usage
      • Approx. 100 ml / m² per layer applied
      • Approx. 100 ml/m² depending on the absorbency of the substrate

    • General information
      • Observe current standards and guidelines for coating wood building elements outdoors (Codes of Practice issued by the German Association of Window and Facade Manufacturers (VFF), Code of Practice No. 18 issued by the German Federal Committee for Paint and the Protection of Material Assets (BFS), guidelines issued by the German Lacquer and Printing Ink Association (VdL) and ift guidelines issued by the Institut für Fenstertechnik).

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.