• Induline GW-390

    Article No. 795005

    Induline GW-390

    Water-based, translucent primer for complex and oversized building elements

    Colour: clear | 7950
    Colour: clear | 7950
    Please choose a colour

    Product specifications

    On delivery

    Binder Acrylate/alkyd resin
    Density (20°C) Approx. 1.01 g/cm³
    Odour Characteristic
    Runout time s in DIN 4 cup Approx. 11.5

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For professional users only
    • For use on exterior wood
    • Soft and hard woods
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking
    • Complex & oversized building elements

    Properties

    • Water-based
    • Good (wet) adhesion
    • Good pore wetting performance
    • Ready to apply by dipping or flow-coating
    • Good flow behaviour on raw and impregnated wood, especially on complex and overdimensioned components
    • Free from film preservation and wood protection biocides
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

    • Application
      • Stir before use
      • Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C
      • By brush / Dipping / Flow coating / Spraying only in closed facilities
      • Application requirements

        Temperature of the material, air and substrate: +15 to +30 °C Processing conditions are between +15 °C and +30 °C at a relative humidity of 40 - 80%

      • Stir well, including during application or after a break in work.

        Qualified specialist companies: brushing, dipping, flow-coating and spraying in closed systems only.

        Once dry, apply further coatings.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 2.5 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Substances in oak may bleed, causing dark discolouration, when coated with water dilutable dispersion stains.

        Apply forced drying to tannin-containing woods.

        The best flow results on Accoya, oak and chestnut are achieved at a pH value of 9.0–9.5, corresponding to an additive content of 0.3–0.5% VP 20829 Additive (0366).

        If the viscosity increases due to evaporation, this must be remedied with water (target viscosity: runout time approx. 23 - 27 s in 3 mm ISO cup).

        Dilute with up to 10% water to improve flow properties in unfavourable conditions (elevated temperatures, low humidity). Add water to make up for any moisture lost through evaporation.

        If foaming occurs in the flow coating system, it is recommended to add 0.2-1.0% VP 9325 defoaming agent - strength 2.

        The system finder on our website www.remmers.com contains coating recommendations for specific wood types to be used when treating windows and exterior doors.

      • Drying

        Recoatable: after approx. 2.5 hours (at 23 °C and 50% RH.) Recoatable with forced drying: after approx. 90 minutes (20 minutes dripping off/50 minutes drying phase (35 - 40 °C)/20 minutes cooling phase)

      • Thinning

        Ready to use; Dilute with water (max. 10 %) if necessary.

    • Working tools / cleaning
      • By brush / Dipping / Flow coating / Spraying only in closed facilities
      • Brush, dipping tank, flow coating system, spraying equipment

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Shelf-life 12 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 80 ml - 120 ml / m² per layer applied
      • 80 - 120 ml/m² per application

      • Depending on the processing method, wood type and wood surface.

    • General information
      • Observe the information sheets “Upkeep and Maintenance of Dipping Tanks and Flow Coating Facilities” and “Information on Workplace Hygiene”.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.