• Protective Sealer

    Article No. 215506

    Protective Sealer

    Solvent-based, transparent, matt protective lacquer

    Colour: clear | 2155
    Size / Quantity

    Product specifications

    On delivery

    Density (20°C) Approx. 0.98 g/cm³
    Degree of gloss Matt

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors
    • For professional users only
    • Interior wood
    • Decorative protection of fire-resistant coatings
    • For areas in which increased requirements are placed on the surface
    • Wall and ceiling panels
    • Schools, restaurants, hospitals, residential and office buildings


    • Solvent-based
    • For protection against humidity and mechanical loading
    • Prevents sticking and contamination of the fire-resistant surface
    • Different degrees of gloss of the fire-resistant material are evened out by the matt finish
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood moisture content max. 15%

    • Application
      • Application temperature: min. 10 °C max. 30 °C
      • By brush / By roller / Airless/airmix spraying
      • Application requirements

        Temperature of the material, air and substrate: from min. +10 °C to max. +30 °C.

      • Stir well.

        Apply with a brush, roller or by spraying.

        Airmix spraying: nozzle size: 0.28 - 0.38 mm, material pressure: 70 - 90 bar, atomiser air pressure: 1 - 2 bar.

        Airless spraying: nozzle size: 0.28 - 0.38 mm, material pressure: 70 - 90 bar.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 24 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

      • Drying

        Dust-dry: after approx. 2 hours
        Fully dry: after approx. 24 hours

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

        If the humidity level is high during drying, clouding may occur.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • By brush / By roller / Airless/airmix spraying
      • Medium-pile lamb's wool roller, solvent-resistant surface brush

        Airless/airmix spraying equipment
        High-performance piston pump, ratio ≥ 30:1
        Remove sieves and filters
        Hose diameter ≥ NW 10
        Whip 1.5-2 m, NW 6, possible
        Use solvent-resistant hoses

      • Clean tools immediately after use with V 101 Thinner.
        Dispose of the remains from cleaning properly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 18 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 18 months.

    • Usage
      • Approx. 50 g / m² per layer applied
      • Max. 50 g/m² (= approx. 50 ml/m²)

    • General information
      • Do not stack treated components.

        Only use Protective Sealer in conjunction with Intumescent Coat.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.