• Wood Cream
    • Wood Cream

    Article No. 271520

    Wood Cream 3 in 1

    Pigmented, transluctent, decorative wood preservative stain for exterior wood protection and finishing

    Colour: light oak (RC-365) | 2715
    Colour: light oak (RC-365) | 2715
    Please choose a colour

    Product specifications

    On delivery

    Density (20°C) Approx. 0.88 g/cm³
    Flash point Approx. 61 °C
    Odour Solvent-like, odourless once dry
    Degree of gloss Silk matt
    Pigmentation Light-fast, highly transparent pigments

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For use on exterior wood
    • Wood without ground contact
    • Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Primer, intermediate and finishing coats

    Properties

    • Solvent-based
    • Low-build stain in brilliant colours
    • Only one coat needed
    • 3 in 1: impregnation, priming and stain
    • Impregnation effect: saturates wood to protect against moisture
    • Diffusion-open protective film: moisture can escape
    • Water-repellent: wet surfaces dry quickly
    • Protection against weathering (constructive protection and the protection provided by the product) reduces the risk of blue stain and rot
    • Film protects coating against blue stain, mould and algae
    • Cream form: no need to stir, non-drip for overhead working
    • Self-levelling
    • Does not flake
    • Subsequent treatment without sanding
    • Preparation
      • Substrate requirements

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Completely remove old coatings (e.g. paints or medium-build stains), bark, bast and dirt.

        Remove loose and torn knots as well as resin that bleeds and clean with a suitable product (e.g. Remmers thinner & brush cleaner).

        Smooth, planed wood surfaces should be sanded and dusted before the coating is applied to ensure better absorption.

        Take appropriate measures to protect adjacent building elements and materials that should not come into contact with the product.

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

    • Application
      • Application temperature: min. 5 °C max. 25 °C
      • By brush / By roller
      • Apply using a brush or roller.

        Apply in the direction of the grain.

        After approx. 30 minutes, check the surface for excess material and smooth it off if necessary.

        After drying, apply a second coat if required.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 12 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        If the surface is overcoated with other products it is recommended to test the adhesion to the substrate.

        Use the clear variant on sheltered exterior surfaces only, such as roof undersides, or as a primer.

        Rainfall may cause water soluble substances to bleed from wood that is rich in such substances, e.g. oak, red cedar, afzelia, redwood, etc. This may lead to the discolouration of light-coloured masonry or render.

        Pre-testing is recommended also on other woods.

        Cut end-grain surfaces at the bottom to create a water-drip edge.

        Apply two subsequent coats of end-grain wood preservative to end-grain wood and cut surfaces in order to protect them against moisture.

        Each layer of stain results in a more intense colour and a glossier finish.

      • Drying

        Approx. 12 hours at 20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

        Drying time may be significantly delayed depending on the type of wood, e.g. larch.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • By brush / By roller
      • Brush with natural bristles, flat brush, velour roller

      • Clean tools immediately after use with thinner and brush cleaner.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • At least 36 months in unopened, original containers stored cool, dry and protected from frost.

    • Usage
      • Total application/absorption rate 200 ml Total / m²
      • Approx. 200 ml/m² in 1-2 coats

    • General information
      • On planed larch and softwoods with a high resin content, the coating may have reduced adhesion and resistance to weathering. This is especially the case on horizontal year rings, knots and areas of winter growth that are high in resin. Maintenance and renovation must be carried out more frequently on these surfaces.
        The only remedy for this is pre-weathering or very coarse sanding (P80).
        If these wood types are rough-sawn, considerably longer maintenance and renovation intervals are to be expected.

        Observe the regulations concerning design principles for wood protection.

        Do not use on horizontal surfaces without drainage slopes and without edge radius, avoid accumulated moisture.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.