• Induline NW-724 naturetouch

    Article No. 509660

    Induline NW-724 naturetouch

    Water-based, naturally matt coating for wood/aluminium constructions

    Colour: clear | 5096
    Colour: clear | 5096
    Please choose a colour
    Size / Quantity

    Product specifications

    On delivery

    Binder Acrylate
    Density (20°C) Approx. 1.03 g/cm³
    Odour Characteristic
    Degree of gloss Cloth matt

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • for dimensionally stable elements
    • For professional users only
    • Soft and hard woods
    • Dimensionally stable wood/aluminium building elements: e.g. wood/aluminium windows and doors
    • Not suitable for exterior surfaces of dimensionally stable wood building elements that are exposed to weather conditions

    Properties

    • Water-based
    • Very natural look and feel
    • Emphasises the natural character of the wood
    • UV-resistant and colourfast
    • Reduces grain emphasis and yellowing of wood substrate
    • Good flow properties
    • Block resistant (in accordance with Code of Practice HO.03)
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

      • Preparations

        If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).

        Pre-treat using a suitable primer & intermediate coat and carry out intermediate sanding if necessary.

        If necessary, protect parapet joints with Induline V-Joint Protection or Induline AF-920.

    • Application
      • Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C
      • Stir before use
      • Airless/airmix spraying
      • The values given are based on undiluted material. The best spraying pattern is achieved if the material has a temperature of 15-20 °C.

        Airless spraying: nozzle size: 0.28-0.33 mm; material pressure: 90-120 bar.

        Air-mix spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar, atomiser air pressure 1-2 bar.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Before coating technically modified woods and wood-based materials, apply the product to a trial surface and conduct a suitability test on the desired area of use.

        Do not use in direct sunlight or at temperatures below +15 °C or above +30 °C.

        Ensure good ventilation.

        Substances in oak may bleed, causing dark discolouration, when coated with water dilutable dispersion stains.

        To prevent any substances in the wood from becoming active, forced drying should be carried out.

      • Drying

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Dilute with water if necessary (max. 5%)

    • Working tools / cleaning
      • Airless/airmix spraying
      • Hand spray gun, automatic spraying equipment

        Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 125 ml - 225 ml / m² per layer applied
      • 125 - 225 ml/m² (plus spraying loss)
        (equivalent to a wet film thickness of 125-225 µm and a dry film thickness of 30-50 µm)

    • General information
      • DIN EN 71-3 "Migration of certain elements":

        This product complies with the limits for the migration of heavy metals to children's toys according to DIN EN 71-3 and thus fulfils one of several further requirements for the safety of children's toys according to the EU "Toy Directive" (2009/48/EC).

        Sealing compounds must be compatible with the coating and may only be applied once the coating has dried thoroughly.

        Only use sealing profiles that are free of plasticisers.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.