• PUR Color Top OS
  • PUR Color Top OS
  • PUR Color Top OS
    • PUR Color Top OS
    • PUR Color Top OS
    • PUR Color Top OS

    Article No. 605530

    PUR Color Top OS

    Pigmented topcoat for OS 11 systems

    Colour: Special colours from 120 kg | 6055
    Size / Quantity

    Product specifications

    On delivery

    Component A

    Density (20°C) 1.68 g/cm³
    Viscosity (25 °C) 1400 mPa s

    Component B

    Density (20°C) 1.05 g/cm³
    Viscosity (25 °C) 2300 mPa s


    Density (20°C) 1.45 g/cm³
    Viscosity (25 °C) 1100 mPa s

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Topcoat in the Remmers Deck OS 11a - II system and Remmers Deck OS 10 M
    • Topcoat in the Remmers Deck OS 14 system in accordance with the maintenance guideline (draft 2016)


    • Lightfast
    • Tough-elastic
    • Can be subjected to mechanical loads
    • Can be subjected to chemical loads
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        Suitable substrates are base layers in the Remmers Deck OS 11a - II system that have been blinded fully broadcast with quartz sand.

    • Preparation
      • Mixing ratio comp. A 73 : comp. B 27
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the base compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Application temperature: min. 10 °C max. 30 °C
      • By brush / By roller
      • Pot life 30 min
      • Application requirements

        Temperature of the material, air and substrate: from min. +10 °C to max. +30 °C.

      • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • By brush / By roller
      • Rubber wiper, epoxy roller, mixer

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101 Thinner.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 0.5 - 0.8 kg/m² binder

    • Application examples
      • Top sealant

        Apply the material using a rubber wiper and then roll cross-wise with a suitable epoxy roller.

        Make sure that no pools form.

        To minimise streaking, roll over the surface again in one direction using a suitable large roller.

        approx. 0.5 - 0.8 kg/m² binder

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C). Slight deviations from these values may arise if the product is worked with on site.

        When coating continuous surfaces, only use materials with the same batch number.

        If dark or highly pigmented colours are used it is possible that, even with very careful application, shadows or light textures appear on the surface. This is due to the product system and does not in any way affect product suitability. In case of doubt set up a trial surface.

        Suitable for vehicle traffic with rubber tyres; not suitable for vehicle loads with metal or polyamide tyres nor for dynamic point loads.

        Abrasive mechanical loads leave traces of wear.

        Observe the instructions for use of the corresponding Remmers Deck OS 11 systems.

        Do not use in enclosed spaces.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        Further information concerning safety during transport, storage and handling as well as on disposal and ecology can be found in the latest Safety Data Sheet.