Article No. 605325

    PUR Color VS OS pro

    Flexible wearing layer

    6053 | PUR Color VS OS pro
    Size / Quantity

    Product specifications

    On delivery

    Component A

    Density (20°C) 1.0 g/cm³
    Viscosity (20 °C) approx. 3400 mPa s

    Component B

    Density (20°C) 1.2 g/cm³
    Viscosity (20 °C) approx. 150 mPa s


    Density (20°C) 1.1 g/cm³
    Viscosity (20 °C) approx. 2000 mPa s

    Once fully cured

    Once fully cured

    Shore D after 28 days approx. 65 (ISO 868)
    Tensile strength approx. 22 N/mm² (DIN EN 196 / ASTM C 109)
    Elongation at break (DIN 53504 S2) approx. 55%

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Crack-bridging wear layer in the system Remmers Deck OS 10 EP pro


    • Can be subjected to mechanical loads
    • Tough-elastic
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The substrate must be dry.

        Suitable substrates include surfaces prepared using Remmers PUA Hybrid OS pro or PUR Color ZS OS pro.

        The specified processing times must be followed.

        If the waiting time is exceeded or unfavourable weather conditions (e.g. rain) are present, apply PUR Primer S (6062) and sand if necessary before applying the wearing layer.

    • Preparation
      • Mixing ratio comp. A 100 : comp. B 47
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the base compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Application temperature: min. 10 °C max. 30 °C
      • Self-levelling coating / Apply standing
      • Pot life 25 min
      • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • Self-levelling coating / Apply standing
      • Notched trowel, notched scraper, suitable mixing equipment

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools and remove any contamination immediately after use and while fresh using Thinner V 103.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • approx. 0.7 - 1.5 kg/m² binder

    • Application examples
      • Base layer for blinded coatings

        Pour the material onto the prepared substrate and then distribute using a suitable tool, e.g. a notched trowel or notched scraper.

        Scatter an excess of fire-dried quartz sand, e.g. grain size 0.7 - 1.2 mm, onto the fresh base layer.

        approx. 0.7 - 1.5 kg/m² binder

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

        Protect the coating against direct contact with water for the first 24 hours after application to prevent blistering.

        Due to the short reaction time, the coating operation must be well planned and prepared.

        The additional material needed to attain the minimum layer thicknesses (wearing layer) and cover the surface texture must be calculated.

        Abrasive mechanical loads leave traces of wear.

        Observe the application information for the Remmers Deck OS systems.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        Further information concerning safety during transport, storage and handling as well as on disposal and ecology can be found in the latest Safety Data Sheet.