Article No. 100825

    Betofix Fill

    PCC fine filler

    Variant
    1008 | concrete grey
    Size / Quantity

    Product specifications

    On delivery

    Flexural tensile strength 28 d: ≥ 7.0 N/mm²
    Compressive strength 1 d: ≥ 10 N/mm²
    7 d: ≥ 25 N/mm²
    28 d: ≥ 30 N/mm²
    Dynamic E-modulus ≥ 15000 N/mm²
    External surveillance QDB and KIWA
    Maximum grain size 0.5 mm
    Capillary water uptake ≤ 0.5 kg/(m²h0.5)
    Water requirement Approx. 14%, equivalent to 0.85 l/6 kg and 3.5 l/25 kg
    Surface tensile strength ≥ 1.5 N/mm²

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use on floors/walls/ceilings indoors and outdoors
    • Concrete replacement according to
      - DIN EN 1504-3
      - Rili-SIB DAfStb 2001
    • Interior and exterior use
    • Evening out concrete surfaces
    • Repair of pores, missing and broken out areas
    • System component OS 4 (OS C) / OS 5a (OS DII)
    • System component PCC/M3 system

    Properties

    • High early strength
    • Good smoothing and adhesion properties
    • Low-stress and crack-free setting
    • Well suited to overhead working
    • Freeze/thaw-resistant
    • Preparation
      • Preparations

        Concrete substrate:
        Stable, clean, dust-free, absorbent
        Observe the applicable technical regulations for the following parameters:
        - Adhesive pull strength of the substrate
        - Minimum roughness/roughness depth

        Pre-wet the substrate so that it is slightly moist.

    • Application
      • Application temperature: min. 5 °C max. 30 °C
      • Mortar pump/ Trowel / Filling knife / Smoothing trowel / Mortar pump
      • Working time
        (+20 °C): Approx. 60 minutes

         

        Layer thickness

        Single layer: 1 - 6 mm
        In broken-out areas: up to 10 mm

         

        Apply product in the desired coating thickness.

        Smooth the surface using a suitable tool.

        Finish the surface once set.

         

        Subsequent processing

        Protect fresh mortar surfaces from wind, direct sunlight, rain and/or frost for at least 3 days so that they do not dry too quickly.

         

        Machine working

        Please contact Remmers Technical Service (phone +49 5432 83900) before applying with machine processing.

         

    • Working tools / cleaning
      • Mortar pump/ Trowel / Filling knife / Smoothing trowel / Mortar pump
      • Mixing tool, notched trowel, trowel, smoothing trowel, plasterer's float, sponge float

        Clean tools with water while the material is still fresh.

    • Storage / shelf life
      • Protect form moisture
      • Shelf-life 12 months
      • If stored in an unopened container and in a dry place, the product will keep for approx. 12 months.

    • Usage
      • Approx. 1.75 kg / mm thick layer / m²
      • Approx. 1.75 kg/m²/mm layer thickness, or approx. 1.75 kg/dm³

    • Application examples
      • - Remmers OS-C / OS 4 System (Betofix Fill + Color PA)

        - Remmers OS-DII / OS 5A System (Betofix Fill + Color Flex)

    • General information
      • The substrate must have an average pull-off strength of at least 1.5 N/mm²

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.