• Induline LW-730 WF
    • Induline LW-730 WF

    Article No. 782020

    Induline LW-730 WF

    Water-emulsified low-build stain

    Colour: clear | 7820
    Colour: clear | 7820
    Please choose a colour

    Product specifications

    On delivery

    Binder Acrylate
    Density (20°C) Approx. 1.01 g/cm³
    Odour Mild
    Degree of gloss Dull matt

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • For professional users only
    • For use on interior and exterior wood
    • Soft and hard woods
    • Building elements with no or limited dimensional stability
    • For decorative design and for protecting laminated wood against dirt during transportation and construction

    Properties

    • Water-based
    • Ready to use
    • Quick drying
    • Easy to apply
    • Block resistant (in accordance with Code of Practice HO.03)
    • Can be stacked wet-on-wet
    • Contains UV blockers to delay yellowing of the wood substrate
    • Free from film preservation and wood protection biocides
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).

    • Application
      • Application temperature: min. 5 °C max. 25 °C
      • Stir before use
      • Brush /Roller / Airless/airmix spraying / Board coating machine
      • Stir well, including during application or after a break in work.

        Apply with a brush, roller or by spraying.

        Once dry, apply further coatings.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 2 h
      • If you wish to use this product in a pigmented version (special colour), please consult Remmers Technical Service beforehand.

        Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Substances in oak may bleed, causing dark discolouration, when coated with water dilutable dispersion stains.

        If you wish to use this product outside its primary area of application (house and hall construction), please consult Remmers Technical Service beforehand.

      • Drying

        Can be overcoated: after approx. 2 hours
        (Practice values at 20°C and 65% relative humidity)

        Forced drying: after approx. 10 minutes flash-off zone (at approx. 20 °C and 65-70% RH) / 30 minutes drying phase (approx. 45 °C, 1 ms air circulation) / 20 minutes cooling phase

        Low temperatures and high humidity delay drying.

      • Thinning

        Ready to use.
        Dilute with water if necessary (max. 5%)

    • Working tools / cleaning
      • Brush /Roller / Airless/airmix spraying / Board coating machine
      • Acrylic brush, flat brush, short-pile roller, airless/airmix spraying equipment, board coating machine, sponge, carpet board, mop

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 80 ml - 120 ml / m² per layer applied
      • 80 - 120 ml/m² per coat

    • General information
      • On planed larch and softwoods with a high resin content, the coating may have reduced adhesion and resistance to weathering. This is especially the case on horizontal year rings, knots and areas of winter growth that are high in resin. Maintenance and renovation must be carried out more frequently on these surfaces.
        The only remedy for this is pre-weathering or very coarse sanding (P80).
        If these wood types are rough-sawn, considerably longer maintenance and renovation intervals are to be expected.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.