• PUR HCL-248/90 High Gloss Colour Varnish

    Article No. 513801

    PUR HCL-248/90 High Gloss Colour Varnish

    Two-component high-gloss topcoat with excellent volume and low time to polishability

    Variant
    PUR HCL-248/90 high gloss
    Colour: special colours | 5138
    Size / Quantity

    Product specifications

    On delivery

    Density (20°C) 1.00 - 1.40 g/cm³
    Runout time s in DIN 4 cup 65 - 90

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors
    • for furniture
    • For professional users only
    • High-quality furniture
    • Wood materials
    • Ideal on surfaces that have been pre-treated with Remmers PUR fillers
    • Finishing coat

    Properties

    • Solvent-based
    • High mechanical resistance
    • Fully resistant to metal rings
    • Very easy to sand and polish
    • High build
    • High hiding power
    • Fire resistant
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood moisture content: 8-12%

      • Preparations

        Wash down with V-890 if necessary.

        The material can be applied directly to a sanded priming film.

        The coating should be applied directly after sanding.

        Prepare insulated MDF panels and solid wood using Remmers PUR Filler.

    • Application
      • Airless/airmix spraying / Flow cup gun
      • Application temperature: min. 18 °C max. 25 °C
      • Stir well.

        Spray application: airless & air-mix procedures

        Flow cup gun: nozzle size: 1.6 - 1.8 mm; atomiser air pressure: 2 - 3 bar.

        Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.

        Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 16 h
      • Isocyanates react with moisture in the air. Always seal the hardener container so that it is air-tight.

        Metallic effects and fluorescent colours (may not be permanently resistant to light depending on the pigmentation) may have a reduced gloss level due to the special pigments used. In this case, we recommend subsequently polishing to a high-gloss finish or coating with PUR HL-211/90. We also recommend that you consult Remmers Technical Service for advice on this special application.

      • Drying

        Dust dry: approx. 30 minutes Touch dry: approx. 60 minutes Can be sanded/overcoated: approx. 16 hours Can be polished: approx. 48 hours Coated products can be stacked: approx. 48 hours

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Dilute with V-893 or V-897 (10 - 30%).

    • Working tools / cleaning
      • Airless/airmix spraying / Flow cup gun
      • Airless/airmix equipment, flow cup gun

      • Clean tools using WV-891 Brush Wash or V-890 Thinner.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Shelf-life 12 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 120 ml - 150 ml / m² per layer applied
      • 120 - 150 ml/m² per coat

    • General information
      • Please refer to the relevant test reports/certificates and the Technical Data Sheet for information on certified products and configurations.

        To preserve the quality of the surface, we recommend regular cleaning and care using a lint-free cotton cloth. Please use solvent-free and silicone-free cleaning agents.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.