Article No. 531005
Transparent, single-component finish with high durability
Downloads & documents
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- Interior wood
- Primer & top coat
- Solid wood & veneers
- Living room & bedroom furniture
- Interior finishing work: e.g. panels, borders, cladding & interior doors
- Shop fitting and trade fair stands
- As a glass lacquer (in combination with Aqua VGA-485)
- Topcoat for Aqua coloured varnishes
- Water-based lacquer that can be sprayed to give an even layer (no milky wet film)
- Good sanding properties
- Good block resistance
- Good flow properties
- Elegant pore pattern
- Resistant to chemicals: DIN 68861, 1B
- Good resistance to a wide range of commercially available hand creams
- Excellent emphasis of the grain
- Surfaces show no tendency to become glossy
- Pleasant feel
- Fire resistant
- 2K-ready: further improvement of the resistance to chemicals and scratches, as well as adhesion to glass, by adding 2% Aqua VGA-485 (isocyanate-free)
The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.
Wood moisture content: 8-12%
Wash off greasy or resin-rich woods/substrates with WV-891 or V-890.
Clean glass using V-890 or UN-894.
Sand wood using P 100 - 180 grit.
Sand panels using P 180 - 320 grit.
Sand lacquer using P 240 - 320 grit.
If colouring is desired, stain the substrate using Aqua KB-004, Aqua BB-007 or Aqua PB-006.
Temperature of the material, air and substrate: from min. +18 °C to max. +25 °C.
Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.
Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.
Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.
After drying and intermediate sanding (P 320 - 400), apply a second coat of the product.
Repeat the process if necessary.
Seal opened containers well and use contents as soon as possible.
Check colour, adhesion and compatibility with the substrate by setting up a trial area.
For a transparent coating over surfaces coated with a coloured varnish, we recommend adding 5-10% Aqua Colour Varnish in the desired colour to the clear varnish.
Dust-dry: after approx. 1 hour Overcoating: after approx. 4 hours Can be stacked: after drying overnight
Practice values at +20 °C and 65% relative humidity.
Low temperatures, poor ventilation and high humidity delay drying.
Ready to use; if necessary dilute with max. 5% water and/or add max. 3% V-490 as a retarding agent.
Working tools / cleaning
Airless/airmix spraying equipment, flow cup gun
Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.
Ensure that any residue from cleaning is disposed of correctly.
Storage / shelf life
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.
100 - 120 ml/m² per coat
Before coating technically modified woods and wood-based materials, apply the coating to a trial surface and conduct a suitability test on the desired area of use.
Please refer to the relevant test reports/certificates and the Technical Data Sheet for information on certified products and configurations.
To preserve the quality of the surface, we recommend regular cleaning and care using a lint-free cotton cloth. Please use solvent-free and silicone-free cleaning agents.
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
Safety / regulations
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.