• Opaque Coating 3in1

    Article No. 270501

    Opaque Coating 3 in 1

    Solvent-based, opaquely pigmented alkyd resin coating for primer, intermediate and finishing coats

    Colour: white (RAL 9016) | 2705
    Colour: white (RAL 9016) | 2705
    Please choose a colour
    Size / Quantity

    Brochures

    product.brochures.loading

    Product specifications

    On delivery

    Binder Alkyd resin combination
    Density (20°C) 1.20 ± 0.05 g/cm³
    Odour Characteristic
    Degree of gloss Silk gloss

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For use on interior and exterior wood
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking
    • Primer, intermediate and finishing coats
    • Biocide-free finishing coat for impregnated wood, e.g. garden furniture
    • Can also be used as a maintenance coat

    Properties

    • Solvent-based
    • High total solids level for greater covering capacity
    • Block resistant (in accordance with Code of Practice HO.03)
    • Free of aromatic compounds
    • Resistant to yellowing
    • Easy to apply
    • Good edge coverage
    • Weatherproof and moisture-regulating
    • Isolating effect against substances contained in the wood
    • Preparation
      • Substrate requirements

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

        The substrate must be clean, dust-free and dry.

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Thoroughly sand any old coatings that are still intact.

        Sand grey and weathered wood surfaces down to sound, bright wood.

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

        Pre-treat exterior wood which requires protection against rot and blue stain with Wood Protection Primer.* (*Use biocides safely. Always read the label and product information before use.)

    • Application
      • Stir before use
      • By brush / By roller
      • Application temperature: min. 5 °C max. 25 °C
      • Stir well.

        Apply using a brush or roller.

        Apply further coats once dry.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 12 h
      • Check the product’s compatibility with the substrate, adhesion and sealing effect by applying a trial coat.

        Cut end-grain surfaces at the bottom to create a water-drip edge.

        Two coats of end-grain wood preservative should first be applied to end-grain wood and cut surfaces in order to protect them against moisture.

        On surfaces that are not exposed to daylight, e.g. the inner surfaces of windows and external doors, alkyd resin systems exhibit a certain degree of dark yellowing, in particular in rebates.

        Bright, intense colours such as yellow, orange and red may have a lower covering capacity as a natural consequence of the pigments used. When using these colours, it is therefore recommended either to first apply a coat of a similar colour with a greater covering capacity, or to apply a second coat in the desired colour.

        When using the product in the workshop or in enclosed spaces, make sure that the area has adequate air circulation and a good supply of fresh air.

        Areas that are being coated or dried should be protected against rain, wind, sunlight and condensation.

      • Drying

        Dust-dry: approx. 4 hours Touch-dry: approx. 6-8 hours Can be overcoated after approx. 12 hours

        Practice values at +20 °C and 65% relative humidity.

        The coating may take significantly longer to dry thoroughly in lower temperatures, at high humidity or if the maximum layer thickness has been exceeded.

        Longer drying times can improve the sealing effect.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • By brush / By roller
      • Brush with natural bristles, mohair roller, foam roller

      • Clean tools immediately after use with thinner and brush cleaner.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Shelf-life 24 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

    • Usage
      • Approx. 50 ml - 70 ml / m² per layer applied
      • Approx. 50 - 70 ml/m² per coat

    • General information
      • The final degree of gloss only sets in approx. 2-3 weeks after application. There may be slight differences in the gloss level depending on the colour.

        On planed larch and softwoods with a high resin content, the coating may have reduced adhesion and resistance to weathering. This is especially the case on horizontal year rings, knots and areas of winter growth that are high in resin. Maintenance and renovation must be carried out more frequently on these surfaces. The only remedy for this is pre-weathering or very coarse sanding (P80). If these wood types are rough-sawn, considerably longer maintenance and renovation intervals are to be expected.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.