Article No. 232303
Weather protection paint for wood and other substrates in indoor and outdoor areas
Downloads & documents
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- For use on interior and exterior wood
- Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
- Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking
- Zinc roof gutters and zinc sheet metal
- Many other different substrates
- Highly opaque
- Does not flake
- Alkali-resistant, including when used on mineral substrates
- Weatherproof and moisture-regulating
- Low solvent, environmentally compatible, mild odour
- Quick drying
Wood building elements with limited or no dimensional stability: wood moisture content max. 18%
Thoroughly remove any dirt, grease and non-adhering old coatings.
Sand grey and weathered wood surfaces down to sound, bright wood.
Remove loose and torn knots as well as resin that bleeds and clean with a suitable product (e.g. thinner & brush cleaner).
Exterior wood that is to be protected against wood-destroying soft rot and blue stain and/or insects should be pre-treated with a suitable wood preservative* [see system products]. (*Use biocides safely. Always read the label and product information before use.)
Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".
To prevent bleeding of substances in the wood, apply a primer coat of Aqua AG-26 Universal Primer when using this product in white or light colours.
To avoid bleeding of substances in the wood into adjoining building elements (e.g. infilling in framework areas), treat the wood all round.
Old weathered carbolineum coatings can only be coated with dark colours. Always test first with a trial coating.
Zinc (galvanised steel):
Clean with an ammonium-based wetting agent, using an abrasive pad. Observe BFS Code of Practice No. 5.
Pre-treat with Aqua AG-26 Universal Primer if the substrate is exposed to increased mechanical stresses.
Substrates should be prepared in accordance with the guidelines for scrub-proof and weather-resistant dispersion paints (DIN 53778).
Thoroughly remove algae and moss from old fibrated cement surfaces. Allow the substrate to dry fully.
Repair damaged render.
Set up a trial area to test whether the product can be used to rework old oil-based coatings.
Stir well and apply quickly using a brush or roller.
Observe the waiting times between coats.
See application examples for substrate-specific set-up.
If using white or light colours, apply 2 primer coats of Aqua AG-26 Universal Primer.
The colour shown on the sample does not appear until the material has dried.
Paint-on-paint contact, e.g. stacking, should be avoided.
Do not use on wood impregnated with boron salts.
Ensure sufficient ventilation when applying indoors.
2 - 4 hours at 20 °C and 65% relative humidity. Exterior wood should be protected from rain for at least 4 hours after coating (danger of washing off).
Low temperatures, poor ventilation and high humidity delay drying.
Dilute with water if necessary.
Working tools / cleaning
Paintbrush with acrylic bristles, flat brush, foam roller
Clean tools immediately after use with water and detergent.
Ensure that any residue from cleaning is disposed of correctly.
Storage / shelf life
At least 36 months in unopened, original containers stored cool, dry and protected from frost.
Approx. 80 - 100 ml/m² per coat If pre-treated with Aqua AG-26 Universal Primer (for light colours): 1 x 100 ml/m² See application examples for substrate-specific set-up
Application examples Impregnation Primer coat Intermediate coat Finishing coat Wood substrates:
old weathered wood substrates, renovation coats on dispersion paints, varnishes and wood preservation stains
If necessary, using Aqua IG-15 Impregnation Primer IT
(in outdoor areas only)
Aqua AG-26 Universal Primer
Aqua AG-26 Universal Primer
Rofalin Acrylic Zinc (galvanised steel):
Zinc, galvanised steel and rigid PVC, renovation coats on old coatings
-- Aqua AG-26 Universal Primer
(for higher requirements)
Rofalin Acrylic Rofalin Acrylic Mineral substrates: Fibre-reinforced cement -- 1-2 x Primer HF Rofalin Acrylic Rofalin Acrylic Fair-faced concrete,
-- Primer H Rofalin Acrylic diluted with 10% water Rofalin Acrylic Old renders, exterior (sanding renders, stable renders) -- Primer HF for sanding, chalky renders;
Primer H for stable renders
Rofalin Acrylic diluted with 10% water Rofalin Acrylic Stable renders, interior (gypsum plasters, lime mortar plaster, fair-faced masonry) -- Rofalin Acrylic diluted with 10% water -- Rofalin Acrylic Renovation coats on stable old dispersion paint coats, synthetic renders -- -- Rofalin Acrylic diluted with 10% water Rofalin Acrylic Gypsum plasterboard -- Primer Hydro F Rofalin Acrylic Rofalin Acrylic Wallpaper, coarse fibres etc. -- Rofalin Acrylic -- Rofalin Acrylic
On planed larch and softwoods with a high resin content, the coating may have reduced adhesion and resistance to weathering. This is especially the case on horizontal year rings, knots and areas of winter growth that are high in resin. Maintenance and renovation must be carried out more frequently on these surfaces. The only remedy for this is pre-weathering or very coarse sanding (P80). If these wood types are rough-sawn, considerably longer maintenance and renovation intervals are to be expected.
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
Safety / regulations
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.