Article No. 065203
Water-repellent impregnation for interior and exterior wood
Product specifications
On delivery
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- For interior and exterior use
- Wood without ground contact
- Wood components with no limited stability (only as primer): e.g. fences, timber-frame constructions, carports, wooden lagging
- Wooden components with limited dimensional stability (only as primer): e.g. folding shutters, profiled boards, garden houses
- Dimensionally stable wood building elements (when used as a primer only): e.g. windows and doors
- Pre-treatment under translucent, opaque and oil coatings
- Playground equipment
Properties
- Water-based: does not give off any unpleasant odours and tools can be cleaned with water
- Free from film preservation and wood protection biocides
- Protects wood against moisture
- Reduces dark discolouration of the wood
- Longer-lasting coating effect: minimises swelling and shrinkage of the wood
- When used with stains: more uniform appearance
- Recyclable: timber building elements (e.g. windows) impregnated with Induline IW-130 can be recycled without restrictions
-
Preparation
-
Substrate requirements
Dimensionally stable wood building elements: wood moisture content 11-15%
Wood building elements with limited or no dimensional stability: wood moisture content max. 18%
The substrate must be clean, dust-free and dry.
-
Preparations
Thoroughly remove any dirt, grease and non-adhering old coatings.
To enhance the effect, the construction should be designed to repel water (avoid horizontal surfaces, open end grains, capillary joints, water and moisture pockets, splashing water contact, sharp edges).
Take appropriate measures to protect adjacent building elements and materials that should not come into contact with the product.
Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".
-
-
Application
-
Stir well.
Apply with a brush, roller or by spraying.
Apply in the direction of the grain.
-
Application instructions
-
Rainfall may cause water soluble substances to bleed from wood that is rich in such substances, e.g. oak, red cedar, afzelia, redwood, etc. This may lead to the discolouration of light-coloured masonry or render.
Only use the product on bare wood.
When applying by spraying, avoid excess material. If necessary, smooth off with a brush after spraying.
On planed wood surfaces and very resinous softwoods, the adhesion and weather resistance of the coating may be reduced. This leads to a shortening of the renovation intervals. We therefore recommend using coarse wood sanding (P 80) or rough-sawn wood.
To achieve the best possible impregnation effect, intermediate sanding should be omitted. If necessary, the surface can be lightly smoothed using an abrasive sponge.
A preliminary test for adhesion and compatibility is required before overcoating with system products not listed.
-
Drying
Low temperatures, poor ventilation and high humidity delay drying.
Drying may take longer depending on the type of wood, e.g. oak, due to substances it contains.
-
Working tools / cleaning
-
Paintbrush with synthetic bristles, flat brush, foam roller, pressure sprayer
Clean tools with water and detergent immediately after use.
Ensure that any residue from cleaning is disposed of correctly.
-
Storage / shelf life
-
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.
Use the contents of open containers as quickly as possible.
-
Usage
-
Approx. 80-120 ml/m² per coat, at least 2 coats required
-
Disposal instructions
-
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
-
-
Safety / regulations
-
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.
-