• Stair & Parquet Varnish

    Article No. 239101

    Stair & Parquet Varnish

    Water-based sealing varnish for application with paintbrush and roller

    Colour: clear silk matt | 2391
    Colour: clear silk matt | 2391
    Please choose a colour
    Size / Quantity

    Product specifications

    On delivery

    Binder Acrylate dispersion/PU dispersion
    Density Approx. 1.03 g/cm³
    Odour Mild
    Degree of gloss Silk gloss, silk matt

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors
    • for stairs
    • for wood floors
    • for interior doors
    • for furniture
    • Interior wood
    • Furniture & interior doors
    • Floorboards, parquet flooring & stairs
    • OSB panels and cork flooring
    • Wall and ceiling panels

    Properties

    • Water-based
    • Water-based
    • Good processing properties
    • Good flow properties
    • Resistant to abrasion and scratches
    • Resistant to chemicals: DIN 68861, 1C
    • Good resistance to a wide range of commercially available hand creams
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood moisture content: 8-12%

        Sand using a sandpaper grit of P150-180.

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Thoroughly sand any old coatings that are still intact.

        Wash off greasy and resin-rich wood with thinner and brush cleaner.

    • Application
      • Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C
      • Stir before use
      • By brush / By roller
      • Stir well.

        Apply using a brush or roller.

        Carry out light intermediate sanding with a foam sanding pad or sandpaper with a grit of P240-320.

        Avoid sanding through.

        Apply a second coat once the first has dried.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Before coating technically modified woods and wood-based materials, apply the product to a trial surface and conduct a suitability test on the desired area of use.

        For especially rugged applications, apply at least 3 coats.

        Do not pour directly onto the substrate as this will cause staining.

        Do not apply more than 2 coats per day.

      • Drying

        Dust-dry: after approx. 1 hour
        Touch-dry: after approx. 2 hours
        Can be overcoated: after approx. 4 hours
        Full load-bearing capacity reached after 7 days

        Practice values at +20 °C and 65% relative humidity.

        Make sure that the area is well ventilated during processing and drying.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Ready to use.
        When applying with a roller, 5% water may be added in order to improve the flow properties.

    • Working tools / cleaning
      • By brush / By roller
      • Brush with synthetic bristles, microfibre roller, mohair roller, foam roller

         

        Clean tools immediately after use with water and detergent.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 24 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

    • Usage
      • Approx. 100 - 120 ml / m² per layer applied
      • 100 - 120 ml/m² per coat

    • General information
      • DIN EN 71-3 "Migration of certain elements":

        This product complies with the limits for the migration of heavy metals to children's toys according to DIN EN 71-3 and thus fulfils one of several further requirements for the safety of children's toys according to the EU "Toy Directive" (2009/48/EC).

        Dust and loose dirt on floors and stairs should be removed regularly using a soft broom or mop.

        Clean once a week as required by mopping with a standard commercially available care product for varnished floors.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.