• BIT 2K Fix

    Article No. 2087830

    BIT 2K Fix [basic]

    Solvent-free, bituminous, two-component insulation board adhesive

    020878 | BIT 2K Fix
    Size / Quantity

    Product specifications

    On delivery

    Base Polystyrene-filled bitumen emulsion
    Density of ready-to-use mixture Approx. 0.70 kg/l
    Curing rate 1 - 3 days

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • Adhesive for insulation boards on mineral and bituminous substrates
    • Adhesive for bonding insulation boards to one another


    • Solvent-free
    • High adhesive strength
    • Resistant to bodies of water aggressive to concrete (DIN 4030 XA3)
    • Preparation
      • Substrate requirements

        Clean, dry, dust-free and capable of supporting a load.

        Waterproofing layers must be completely dry.

        Prime absorbent mineral substrates with Kiesol MB.

    • Preparation
      • Combination container

        Break up the powder component before adding to the bitumen emulsion.

        Remove any dried material adhering to the edge of the bucket.

        Briefly stir the bitumen base material.

        Add the entire quantity of broken-up powder component to the bitumen emulsion.

        Mix for approx. 30 seconds, stop mixing and allow the air introduced during mixing to escape.

        Remove the powder adhering to the side.

        Resume mixing and continue for at least 2 minutes.

        Leave the anchor stirrer near the base throughout the mixing time.

        See mixing instructions.

    • Application
      • Application temperature: min. 5 °C max. 30 °C
      • Application by filling knife / Trowel application
      • Working time min. 1 h
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +30 °C

      • Ground moisture/non-pressing water (W1-E)

        Apply 6-8 dots of adhesive to the insulation boards and bond to the building element by pushing down with uniform pressure and floating into position.

        For the water impact class "ground moisture/non-pressing water", we also recommend bonding the insulation boards over their entire surface.


        Pressing water (W2-E)

        Using the material, bond the entire surface area of the insulation boards, including the edges, to the building element in accordance with the official specifications.

    • Application instructions
      • In the case of liquid-applied waterproofing materials, direct sunlight and/or wind exposure can cause accelerated skin formation and accompanying blistering.

        Insulation boards must be firmly fixed at the base point (e.g. projecting foundation) and laid in a bond without joints.

        Until the foundation pit has been filled in, secure the insulation boards so that they cannot slip or slide.

        Protect freshly bonded panels from rear moisture penetration.

        To avoid thermal stresses, the excavation pit must be backfilled promptly.

        In the base area, the base insulation boards must be additionally secured above the ground, see also the processing instructions of the base insulation board manufacturer.

    • Working tools / cleaning
      • Anchor stirrer, scoop, notched trowel, smoothing trowel

        Clean tools with water immediately after use.

        Remove dried-on material using V 101 Thinner (0978).

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Min. 1.5 l/m²

      • Depending on the substrate properties and type of bonding

    • General information
      • The characteristic data of the product were calculated under laboratory conditions at 20°C and 65% relative humidity.

        Current regulations and legal requirements must be taken into account and deviations from these must be agreed separately.

        The relevant test certificates must be observed when planning and carrying out work.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.