• Aqua NEL-419/05 Natural Effect Varnish tif
  • Aqua NEL-419/05 Natural Effect Varnish
    • Aqua NEL-419/05 Natural Effect Varnish tif
    • Aqua NEL-419/05 Natural Effect Varnish

    Article No. 530905

    Aqua NEL-419/05 Natural Effect Varnish

    Clear, single-component finish for a natural wood look with high durability

    Remmers Button 2K Ready Aqua VGA-485
    Colour: clear, cloth matt | 5309
    Size / Quantity

    Product specifications

    On delivery

    Binder Acrylate dispersion
    Density (20°C) Approx. 1.04 g/cm³
    Odour Characteristic

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors
    • for interior doors
    • for furniture
    • For professional users only
    • Interior wood
    • Especially suited to light and light stained woods: oak, maple, ash, birch, spruce, pine
    • Primer & top coat
    • Solid wood & veneers
    • Living room & bedroom furniture
    • Interior finishing work: e.g. panels, borders, cladding & interior doors

    Properties

    • Water-based
    • For coatings that are not perceptible by sight or touch
    • Good block resistance
    • Resistant to chemicals: DIN 68861, 1B (except for alcohol)
    • Good resistance to a wide range of commercially available hand creams
    • Lightfast
    • Surfaces do not become shiny
    • Fire behaviour according to DIN EN 13501-1: B-s1,d0 on suitable substrates
    • Suitable for interior finishing of ships (IMO)
    • 2K-ready: increased resistance to chemicals, disinfectants, abrasion & scratches, and adhesion to glass, with the addition of 2% Aqua VGA-485.
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood moisture content: 8-12%

      • Preparations

        Wash off greasy or resin-rich woods/substrates with WV-891 or V-890. Use UN-894 indoors on the construction site. Ensure good ventilation for solvents.

        Sand wood using P 100 - 180 grit.

        If colouring is desired, stain the substrate using Aqua KB-004, Aqua BB-007 or Aqua PB-006.

    • Application
      • Application temperature: min. 18 °C max. 25 °C
      • Stir before use
      • Airless/airmix spraying / Flow cup gun
      • Stir well.

        Spray.

        Flow cup gun: nozzle size: 1.8 - 2.0 mm; atomiser air pressure: 2 - 3 bar.

        Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.

        Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.

        After drying and intermediate sanding (P 320 - 400), apply a second coat of the product.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Before coating technically modified woods and wood-based materials, apply the product to a trial surface and conduct a suitability test on the desired area of use.

        Varnish open-pored woods to fill the pores.

      • Drying

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

    • Working tools / cleaning
      • Airless/airmix spraying / Flow cup gun
      • Airless/airmix spraying equipment, flow cup gun

        Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 80 ml - 120 ml / m² per layer applied
      • 80 - 120 ml/m² per coat

    • General information
      • DIN EN 71-3 "Migration of certain elements":

        This product complies with the limits for the migration of heavy metals to children's toys according to DIN EN 71-3 and thus fulfils one of several further requirements for the safety of children's toys according to the EU "Toy Directive" (2009/48/EC).

        Please refer to the relevant test reports/certificates and the Technical Data Sheet for information on certified products and configurations.

        To preserve the quality of the surface, we recommend regular cleaning and care using a lint-free cotton cloth. Please use solvent-free and silicone-free cleaning agents.

        For applications in accordance with the Marine Equipment Directive, the maximum wet application quantity is 2 x 120 µm.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.