• Crete Agrar Top

    Article No. 654503

    Crete Agrar Top

    Protective coating

    Colour: grey | 6545
    Size / Quantity

    Product specifications

    On delivery

    Mixture (3C)

    Density (20°C) 1.53 g/cm³ (3K mixture)
    Viscosity (25 °C) 1300 mPa s (3K mixture)

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Protective coating for slatted floors
    • Protective coating for feed fences
    • Protective coating for concrete surfaces in the agricultural industry


    • High abrasion resistance
    • High chemical resistance
    • Non-slip, matt surface
    • Preparation
      • Substrate requirements

        Permitted for use on the following substrates only: slatted floors, concrete floors and bonded screeds

        Heavily damaged slatted floors (visible coarse aggregate) are not suitable for coating and must be replaced if necessary.

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The adhesive pull strength of the surface after priming must be at least 1.5 N/mm² on average (smallest single value min. 1.0 N/mm²), compressive strength at least 25 N/mm².

        The substrates may be slightly damp but must not have a film of liquid.

        Concretemax. 6 m% moisture

        Cement screedmax. 6 m% moisture

      • Preparations

        Prepare the substrate by suitable means, e.g. steel ball jetting or diamond grinding, so that it meets the requirements specified above.

        Use a high-pressure cleaner with rotating "dirt blaster" to remove all traces of dirt or release agent from slatted floors.

        Fill broken out or missing areas in the substrate with the Remmers PCC System flush with the surface.

    • Application
      • Application temperature: min. 10 °C max. 20 °C
      • By brush / By roller
      • Pot life 15 min
      • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • By brush / By roller
      • Rubber scraper, epoxy roller, Patent Disperser

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 9 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 9 months.

    • Usage
      • See application examples

    • Application examples
      • Coating

        Apply the material to the prepared surface and spread evenly using a suitable tool, e.g. an epoxy roller.

        On slatted floors, the inner faces of the slats must also be coated.

        Two coats must be applied.

        Per coat: min. 0.4 kg/m²

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        The resulting surface texture is strongly influenced by the conditions on site and the application method. Therefore, surface texture is not covered by product liability.

        Low thickness and low temperature can affect the visual effect of the finished surface.

        Abrasive mechanical loads leave traces of wear.

        Suitable for vehicle traffic with rubber tyres; not suitable for vehicle loads with metal or polyamide tyres nor for dynamic point loads.

        The material is not generally colour-fast.

        In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.

        If at least two load types occur simultaneously (chemical, mechanical, thermal stresses), limited resistance is to be expected.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        Further information concerning safety during transport, storage and handling as well as on disposal and ecology can be found in the latest Safety Data Sheet.