• Color LA Fill

    Article No. 056010

    Color LA Fill

    "True" silicone resin paint with filling properties

    Colour: white | 0560
    Colour: white | 0560
    Please choose a colour
    Size / Quantity

    Product specifications

    On delivery

    Binder Silicone resin emulsion
    Density (20°C) 1.50 g/cm³
    pH value Approx. 8.5
    Pigmentation Light-fast, alkali-resistant oxide pigments
    Viscosity Approx. 4000 mPa∙s

    Once fully cured

    Once fully cured

    Degree of gloss Matt, mineral character
    Water absorption coefficient
    (DIN 52617)
    w ≤ 0.1 kg/(m² ∙ h0.5)
    Water vapour permeability
    (DIN 52615)
    sd ≤ 0.05 m

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • Porous, mineral building materials
    • Load-bearing silicate, silicone and matt dispersion coatings
    • Synthetic resin renders
    • Surfaces with different roughness levels and hairline cracks
    • Intermediate coat under Silicone Resin Paint LA


    • Water-based
    • Fibre-reinforced
    • Water repellent w ≤ 0.1 kg/(m²∙h0.5)
    • Highly water vapour diffusion capable sd ≤ 0.05 m
    • Does not inhibit carbonation
    • Low-stress
    • Matt, mineral character
    • Fine-sand, coarse texture
    • Preparation
      • Substrate requirements

        Dry, clean, free of dust and cracks (except hairline cracks) and capable of supporting a load.

        Free of salts known to be damaging to building materials.

      • Preparations

        Use Primer Hydro HF to prime mineral substrates capable of supporting a load.

        Use Primer Hydro HF to prime any sanding, firmly adhering substrates.

    • Application
      • Application temperature: min. 5 °C max. 25 °C
      • By brush / By roller / Filling knife / Airless/airmix spraying
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +25 °C

      • Stir well.

        Coat the surface using a suitable tool.

        Apply one coat of the material to even out the texture.

        Wait at least 24 hours before applying subsequent layers.

    • Application instructions
      • Take appropriate measures to protect adjacent building elements and materials that should not come into contact with the product.

        When coating continuous surfaces, only use materials with the same batch number.

        Intensive colours, such as yellow, red, etc. may have a lower hiding power due to their pigments. Apply an additional coat if required.

        Protect freshly treated surfaces from driving rain, wind, sunlight and condensation.

    • Working tools / cleaning
      • By brush / By roller / Filling knife / Airless/airmix spraying
      • Brush, surface brush, lamb's wool roller, scraper, stainless steel trowel and airless spraying equipment

      • Clean tools with water while the material is still fresh.

        Clean splashed material with water while the material is still fresh.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Total application/absorption rate 0.3 kg - 0.5 kg Total / m²
      • Approx. 0.3 - 0.5 kg/m²

      • Application rates may vary depending on the condition of the surface.

        Apply to a large enough trial area to determine the precise amount required.

    • General information
      • Current regulations and legal requirements must be taken into account and deviations from these must be agreed separately.

        The relevant test certificates must be observed when planning and carrying out work.

        Always set up a trial area/trial areas first.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.