• Historic Kalkfarbe

    Article No. 656910

    Color CL Historic

    Lime paint without organic binders

    Colour: white | 6569
    Size / Quantity

    Product specifications

    On delivery

    Binder Dispersed white hydrated lime
    Density (20°C) 1.54 g/cm³
    pH value > 11
    Viscosity 3500 mPa∙s

    Once fully cured

    Once fully cured

    Colour White
    Degree of gloss Cloth matt
    Water absorption coefficient
    (DIN 52617)
    Water vapour permeability
    (DIN 52615)
    sd < 0.01 m

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors
    • Porous, mineral building materials in interior areas
    • Preservation of historical monuments
    • Eco-friendly construction


    • Water-based
    • Capillary-active
    • Highly water vapour diffusible
    • Good hiding power
    • Free from organic binder additives
    • Free from solvents and plasticizers
    • Free from preservatives
    • With a mineral water base
    • Does not contain titanium dioxide
    • Preparation
      • Substrate requirements

        Dry, clean, free of dust and cracks (except hairline cracks) and capable of supporting a load.

        Free of salts known to be damaging to building materials.


      • Preparations

        Pre-wet the substrate.

        Use Historic Lime Wash to level out any textural unevenness.

    • Application
      • Application temperature: min. 5 °C max. 25 °C
      • By brush / By roller
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +25 °C

      • Stir well and apply quickly using a brush or roller.

        2 coats required.

        Observe a waiting time of at least 24 hours between coats.

        To reduce chalking, coated surfaces should be subsequently wetted several times.

    • Application instructions
      • Check the absorbency of the substrate on a sufficiently large test area.

        To prevent a crust forming, work wet-on-wet in a single operation.

        When coating continuous surfaces, only use materials with the same batch number.

        The final colour after drying and hardening depends on the absorptive capacity of the substrate, the ambient conditions, processing and subsequent treatment.

        Substrates with moisture penetrating from the rear can cause discolouration.

        Take appropriate measures to protect adjacent building elements and materials that should not come into contact with the product.



      • Drying

        Touch-dry: 4 to 6 hours
        Recoatable: 24 hours

        The characteristic data of the product were calculated under laboratory conditions at 20°C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        The material can be diluted with up to 10% water.

    • Working tools / cleaning
      • By brush / By roller
      • Brush, flat brush, lambskin roller

      • Clean tools, equipment and any splashed material immediately with water while still fresh.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx.0.2 - 0.25 kg / m² per layer applied
      • Approx. 0.2 - 0.25 kg/m² per coat

      • 2 coats required.

        Application rates may vary depending on the condition of the surface.

        Apply to a large enough trial area to determine the precise amount required.

    • General information
      • Deviations from applicable regulations must be agreed separately.

        The relevant test certificates must be observed when planning and carrying out work.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.