• Multi-Purpose Varnish 3 in 1

    Article No. 774401

    Multi-Purpose Varnish 3 in 1

    Water-based, opaque sealing varnish for use as primer, intermediate and final coating for wood and other substrates

    Colour: white (RAL 9016) | 7744
    Colour: white (RAL 9016) | 7744
    Please choose a colour
    Packaging unit

    Product specifications

    On delivery

    Density (20°C) Approx. 1.27 g/cm³
    Odour Characteristic
    Degree of gloss Silk matt

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For use on interior and exterior wood
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking
    • Sealing primer, intermediate and final coat
    • Can also be used as a maintenance coat
    • Wooden ceilings and wood panelling
    • Zinc roof gutters and zinc sheet metal
    • Radiators
    • Rigid PVC
    • Aluminium (not anodised)
    • Many other different substrates

    Properties

    • Water-based
    • Water-based
    • Ventilating effect
    • Isolating effect against substances contained in the wood
    • Inhibits rust from screws and nail heads
    • Highly weather-resistant and low-chalking
    • Good edge coverage
    • Weatherproof and moisture-regulating
    • Resistant to yellowing
    • Very resistant to dirt
    • Very good adhesion to the substrate
    • Block resistant (in accordance with Code of Practice HO.03)
    • Reduces discolouration due to nicotine
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

         

        Wood substrates:

        Thoroughly sand any old coatings that are still intact.

        Sand grey and weathered wood surfaces down to sound, bright wood.

        Remove loose and torn knots as well as resin that bleeds and clean with a suitable product (e.g. V 101 thinner, thinner & brush cleaner).

        Pre-treat exterior wood requiring protection against soft rot and blue stain with Remmers Wood Preservative Primer* - not necessary for interior wood. (*Use biocides safely. Always read the label and product information before use.)

        The drying times must be observed.

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

         

        Rigid PVC and aluminium (not anodised):

        Use an abrasive pad to apply an ammoniacal wetting agent. Observe BFS Code of Practice No. 22 for rigid PVC and BFS Code of Practice No. 6 for aluminium.

         

        Load-bearing old coatings:

        Remove any old coatings not capable of supporting a load, making sure not to leave any residue.

        Only apply coatings to non-chalking substrates that are capable of bearing a load.

        Refer to BFS Leaflet No. 20.

         

        Zinc (galvanised steel):

        Clean with an ammonium-based wetting agent, using an abrasive pad. Observe BFS Code of Practice No. 5.

        In the case of elevated mechanical stresses, pre-treat with Universal Primer.

         

        Iron, steel:

        Derust thoroughly. Remove scale layers and rolling skin (derust manually to SA 3 standard of cleanliness). The best results are achieved if the substrate has been sand blasted to SA 2.5 standard of cleanliness (DIN EN ISO 12944-4).

        Round off sharp edges and ridges.

        Refer to BFS Leaflet No. 20.

    • Application
      • Stir before use
      • By brush / By roller / Airless/airmix spraying
      • Application temperature: min. 5 °C max. 25 °C
      • Application requirements

        Temperature of the material, air and substrate: min. +5 °C to max. +25 °C

      • Stir well.

        Apply with a brush, roller or by spraying.

        Apply further coats once dry.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 6 h
      • Check the product’s compatibility with the substrate, adhesion and sealing effect by applying a trial coat.

        Areas that are being coated or dried should be protected against rain, wind, sunlight and condensation.

      • Drying

        Dust-dry: 1 - 2 hours Ready for overcoating: approx. 6 hours

        Practice values at +20 °C and 65% relative humidity.

        The coating may take significantly longer to dry thoroughly in lower temperatures, at high humidity or if the maximum layer thickness has been exceeded.

        Longer drying times can improve the sealing effect.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • By brush / By roller / Airless/airmix spraying
      • Acrylic brush, flat brush, foam roller, spraying equipment

      • Clean tools immediately after use with water and detergent.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Shelf-life 24 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

    • Usage
      • Approx. 100 - 120 ml / m² per layer applied
      • 100 - 120 ml/m² per coat 2 coats required.

    • Application examples
      • Application examplesStandardsCleaningInstructionsBase coatIntermediate coatFinal coat
        WoodPlease refer to BFS Code of Practice No. 18
        Remove all traces of dirt, grease and non-adhering old coatings. Remove loose and torn knots and bleeding resin, and clean (e.g. with thinner and brush cleaner). Depending on the wood substrate and load class, we recommend setting up a trial surface to check the adhesion/sealing effect
        Wood Preservative Primer* (outdoors, protection against blue stain and soft rot)
        Multi-Purpose Varnish 3 in 1
        Multi-Purpose Varnish 3 in 1
        Rigid PVC
        Please refer to BFS Code of Practice No. 22
        Remmers thinner and brush cleaner or ammoniacal cleaning agent with abrasive clothDepending on the PVC type and load class, we recommend setting up a trial surface to check the adhesion       ---
        Multi-Purpose Varnish 3 in 1Multi-Purpose Varnish 3 in 1
        Aluminium (not anodised)
        Please refer to BFS Code of Practice No. 6Remmers thinner and brush cleaner or ammoniacal cleaning agent with abrasive clothDepending on the aluminium type and load class, we recommend setting up a trial surface to check the adhesion

              ---


        Multi-Purpose Varnish 3 in 1Multi-Purpose Varnish 3 in 1
        Load-bearing old coatings
        Please refer to BFS Code of Practice No. 20
        Remove all traces of non-adhering substrates. Coatings may only be applied to non-chalking substrates that are capable of bearing a load.
        Depending on the old coating, we recommend setting up a trial surface to check the adhesion      ---Multi-Purpose Varnish 3 in 1Multi-Purpose Varnish 3 in 1


        Zinc gutters and sheeting

        Please refer to BFS Code of Practice No. 5

        Remmers thinner and brush cleaner or ammoniacal cleaning agent with abrasive cloth

        Depending on the zinc type and load class, we recommend setting up a trial surface to check the adhesion

        With Universal Primer, only in exceptional cases
        Multi-Purpose Varnish 3 in 1Multi-Purpose Varnish 3 in 1
        Iron and steelPlease refer to BFS Code of Practice No. 20Remove all traces of rust, rolling skin, scale and welding residue mechanically until a shiny metallic surface is visible.Degree of purity SA 2.5 (jet blasting) and ST3 (mechanical) according to DIN EN ISO 12 944-4. In addition, sharp edges and burrs must be rounded off.Universal Primer Universal Primer
        Multi-Purpose Varnish 3 in 1

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.