• Induline GL-250
    • Induline GL-250

    Article No. 266010

    Induline GL-250

    Solvent-based, white primer with film preservative

    Colour: white | 2660
    Size / Quantity

    Brochures

    product.brochures.loading

    Product specifications

    On delivery

    Binder Special alkyd resins
    Density (20°C) Approx. 0.99 g/cm³
    Odour Solvent-like
    Degree of gloss Matt
    Preservative 3-iodo-2-propynyl butylcarbamate
    Viscosity (20 °C) 55 s in ISO cup 3 mm

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For professional users only
    • For use on exterior wood
    • Soft and hard woods
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking

    Properties

    • Solvent-based
    • Good flow characteristics on untreated and impregnated wood
    • Isolating effect against substances contained in the wood
    • Film preserver protects against microbial damage
    • Good pore wetting performance
    • Outstanding (wet) adhesion
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

    • Application
      • Stir before use
      • By brush / Dipping / Flow coating / Spraying only in closed facilities
      • Application temperature: min. 5 °C max. 30 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +5°C to max. +30 °C.

      • Stir well, including during application or after a break in work.

        Qualified specialist companies: brushing, dipping, flow-coating and spraying in closed systems only.

        After drying, the treated wood can be finished with acwater-based or solvent-based coating system.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 16 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        If the viscosity increases due to evaporation, this must be corrected using V 101 Thinner (target viscosity: runout time approx. 55 s in ISO cup 3 mm).

        The product's sealing effect may be impaired if it is diluted too thinly, if the wood is too wet or if the recommended coating sequence, application volumes and drying times are not observed.

      • Drying

        Dust-dry: after approx. 3.5 hours Overcoating: after approx. 16 hours (at 20 °C and 65% RH)

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        If necessary with max. 10% V 101 Thinner.

    • Working tools / cleaning
      • By brush / Dipping / Flow coating/ Spraying tunnel
      • Brush, dipping tank, flow coating facility, spraying tunnel

      • Clean tools immediately after use with V 101 Thinner. Dispose of the remains from cleaning properly.

    • Storage / shelf life
      • Shelf-life 24 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

    • Usage
      • Approx. 80 ml - 100 ml / m² per layer applied
      • Approx. 80 - 100 ml/m² per coat

    • General information
      • Ensure good aeration and ventilation in particular in series production.

        Sealing compounds must be compatible with the coating and may only be applied once the coating has dried thoroughly.

        Do not use on wood intended to come into direct contact with food or feed.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.

        Do not use on wood intended to come into direct contact with food or feed.