• Induline SW-935
  • Induline SW-935
    • Induline SW-935
    • Induline SW-935

    Article No. 378605

    Induline SW-935

    Water-based, clear impregnation, primer and sanding primer

    Colour: clear | 3786
    Packaging unit

    Product specifications

    On delivery

    Binder Acrylate copolymer/alkyd emulsion
    Density (20°C) Approx. 1.005 g/cm³
    Odour Characteristic

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For professional users only
    • For use on interior and exterior wood
    • Soft and hard woods
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking
    • Undiluted: primer for aluminium-clad wood windows
    • 1:1 with water: impregnation with no active ingredients
    • 1:3 with water: washing aid

    Properties

    • Water-based
    • Quick and easy to use
    • Quick-drying and easy to sand
    • Strengthens wood
    • Raises the fibres, enabling them to be removed during the first sanding operation
    • Reduces spotting when used in combination with coloured primers
    • High-yielding concentrate
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

    • Application
      • Stir before use
      • Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C
      • Application
      • Application requirements

        Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C.

      • Stir well, including during application or after a break in work.

        Application by brush, dipping, flow coating, spraying.

        Once dry, apply further coatings.

        Cannot be used as a replacement for wood preservative.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        The best flow results on Accoya, oak and chestnut are achieved at a pH value of 9.0–9.5, corresponding to an additive content of 0.3–0.5% VP 20829 Additive (0366).

        If foaming occurs in the flow coating system, it is recommended to add 0.2-1.0% VP 9325 defoaming agent - strength 2.

      • Drying

        Dust-dry: after approx. 30 minutes Overcoating: after approx. 4 hours (at 23 °C and 50% RH) If force drying is used, can be overcoated: after approx. 90 minutes (20 minutes dripping/50 minutes drying phase (35-40 °C)/20 minutes cooling phase)

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Concentrate can be diluted up to a ratio of 1:3 with water.

    • Working tools / cleaning
      • Application
      • Brush, dipping tank, flow coating facility, spraying equipment

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Shelf-life 12 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Ca. 30 ml – 90 ml/m² per layer applied
      • 30 - 90 ml/m² per coat (depending on the area of application)

    • General information
      • Observe the information sheets “Upkeep and Maintenance of Dipping Tanks and Flow Coating Facilities” and “Information on Workplace Hygiene”.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.