• Crete Filler TF 60 Set

    Article No. 686710

    Crete TF 60

    PU concrete primer and sealer

    Colour: Crete TF 60 | 6867
    Size / Quantity

    Product specifications

    On delivery

    Mixture

    Density (20°C) 1.51 g/cm³ (4-component mixture)

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Primer for chemically resistant systems
    • Sealer for chemically resistant systems
    • Top seal for blinding layers in chemically resistant systems

    Properties

    • High chemical resistance
    • High mechanical resistance
    • Water vapour diffusion capable
    • Preparation
      • Substrate requirements

        Suitable substrates: concrete and cementitious bonded screed only.

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The tensile strength of the surface of the substrate must be at least 1.5 N/mm² on average (smallest individual value of at least 1.0 N/mm²), and the compressive strength must be at least 25 N/mm².

        Concretemax. 6 m% moisture

        Cement screedmax. 6 m% moisture

      • Preparations

        Prepare the substrate by suitable means, e.g. steel ball jetting or diamond grinding, so that it meets the requirements specified above.

        Fill broken out or missing areas in the substrate with the Remmers PCC System flush with the surface.

        Depending on the requirements of the system, make suitable anchoring cuts into the substrate.

    • Application
      • By brush / By roller
      • Pot life 10 min
      • Application temperature: min. 10 °C max. 20 °C
      • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • By brush / By roller
      • Rubber scraper, trowel, epoxy roller, mixer, compulsory mixer if necessary

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101 Thinner.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 6 months
      • If stored in unopened original containers, in a cool, dry place protected from frost: at least 12 months for components B and D, and at least 6 months for components C and A.

    • Usage
      • See Application Examples

    • Application examples
      • Sealing

        Immediately distribute the material with a rubber squeegee and subsequently roll in over in one direction with a suitable epoxy roller.

        approx. 0.4 kg/m²

      • Head seal

        Immediately distribute the material with a rubber squeegee and subsequently roll in over in one direction with a suitable epoxy roller.

        min. 0.6 kg/m² depending on the blinding material

      • Primer

        Apply the mixed resin generously to the surface. Distribute with a suitable tool, e.g. rubber blade, and work into the substrate with an epoxy roller so that pores in the surface of the substrate are completely filled.

        It may be necessary to apply several layers.

        approx. 0.4 kg/m²

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        The resulting surface texture is strongly influenced by the conditions on site and the application method. Therefore, surface texture is not covered by product liability.

        PU concretes in general are functional floor coverings with low requirements with regard to appearance and are generally not colour-fast.

        Even if the flooring is correctly installed, differences in colour, marks made during application, streaking and slight formation of pools cannot be excluded.

        Due to the short reaction time, the coating operation must be well planned and prepared.

        Low thickness and low temperature can affect the visual effect of the finished surface.

        Abrasive mechanical loads leave traces of wear.

        Suitable for vehicle traffic with rubber tyres; not suitable for vehicle loads with metal or polyamide tyres nor for dynamic point loads.

        In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.

        The resistance to chemical substances must be assessed with regard to the temperature of the medium (see chemical resistance list).

        Anti-slip floors naturally require more cleaning effort than smooth surfaces. Therefore, the use of cleaning machines with soft brushes is recommended.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.