Article No. 666831

Epoxy ESD Color 3K

ESD-compliant coating

Colour: special colours > 150 kg | 6668
Size / Quantity

Product specifications

On delivery

Component A

Density (20°C) 1.43 g/cm³
Viscosity (25 °C) 1850 mPa s

Component B

Density (20°C) 1.06 g/cm³
Viscosity (25 °C) 110 mPa s

Mixture (3C)

Density (20°C) 1.60 g/cm³

Once fully cured

Once fully cured

Flexural tensile strength 27.0 N/mm² *
Compressive strength 31.3 N/mm² *
Shore D after 28 days 65

* Epoxy resin mortar 1 : 3 with standard sand

The stated values represent typical product characteristics and are not to be construed as binding product specifications.

Field of application

  • Self-levelling coating for ESD protected areas

Properties

  • Dissipative / ESD-compliant
  • Can be subjected to mechanical loads
  • Can be subjected to chemical loads
  • Anti-slipping version possible
  • Suitable for hand pallet trucks and forklift trucks
  • Physiologically harmless once fully cured
  • Preparation
    • Substrate requirements

      The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

      The adhesive pull strength of the surface after priming must be at least 1.5 N/mm² on average (smallest single value min. 1.0 N/mm²), compressive strength at least 25 N/mm².

      Suitable Remmers epoxy primers, epoxy scratch coats or epoxy mortars must always be used.

    • Preparations

      Before the application of the product a smooth surface must be produced, e.g. with a scratch coat.

      Refer to the current Technical Data Sheet for detailed information on the single products.

      Epoxy Conductive must be applied according to the current Technical Data Sheet as transverse conducting layer.

  • Application
    • Application temperature: min. 12 °C max. 30 °C
    • Self-levelling coating / Apply standing
    • Pot life 25 min
    • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

  • Working tools / cleaning
    • Self-levelling coating / Apply standing
    • Toothed trowel, notched spreader, mixing apparatus, spiked roller

    • More detailed information can be found in the Remmers Tool Programme.

      Clean tools, equipment and splashed material immediately while fresh with V 101.

      Take suitable protective and waste disposal measures when cleaning.

  • Storage / shelf life
    • Store frost-free
    • Protect form moisture
    • Shelf-life 12 months
    • If stored unopened in the original container and kept cool, dry and protected from frost, min. 12 months (component A)/min. 24 months (component B).

  • Usage
    • See application examples

  • Application examples
    • Coating

      Pour the material onto the prepared substrate and then distribute using a suitable tool, e.g. a notched trowel or notched scraper.

      Afterwards roll over with a (metal) spiked roller.

      The stated approximate application quantities refer to smooth, level substrates.

      approx. 2.5 - 3.0 kg/m² mixture

  • General information
    • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

      When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

      Due to the black transverse conducting layer, poorly covering colours are not to be used.

      Before the application of the covering layer, the correct functioning of the transverse conducting layer and of the connections must be proved and registered in a measurement report.

      Low levels of air humidity can cause a higher discharge resistance, uneven or thicker layers can even lead the coating to not be conductive at all.

      Before checking the ESD values, we recommend cleaning the ESD shoes, the electrodes and the floor coating with isopropyl alcohol or ethanol (95%) and waiting until it has evaporated.

      In case of possible permanent exposure to water or prolonged accumulations of moisture, the formation of white stains on the surface is possible. This does not affect the technical properties of the coating.

      Low thickness and low temperature can affect the visual effect of the finished surface.

      Abrasive mechanical loads leave traces of wear.

      High concentrated loads can leave marks on the impact resistant coating.

      Exposure to vehicles with metal or polyamide tyres as well as dynamic concentrated loads can cause faster wearing of the coating.

      Epoxy resins are generally not colourfast when exposed to UV light or weather.

      In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.

      Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

  • Disposal instructions
    • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

  • Safety / regulations
    • For professional users only!

      For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet and the brochure entitled "Epoxy Resins in the Construction Industry and the Environment", issued by Deutsche Bauchemie e.V. (3rd edition 2022).

Accessories