• PUR Color ZS
  • PUR Color ZS
  • PUR Color ZS
  • PUR Color ZS
    • PUR Color ZS
    • PUR Color ZS
    • PUR Color ZS
    • PUR Color ZS

    Article No. 682626

    PUR Color ZS

    Intermediate or wearing layer

    Variant
    6826 | PUR Color ZS
    Size / Quantity

    Product specifications

    On delivery

    Component A

    Density (20°C) 1.46 g/cm³
    Viscosity (25 °C) 500 mPa s

    Component B

    Density (20°C) 1.04 g/cm³
    Viscosity (25 °C) 4000 mPa s

    Mixture

    Density (20°C) 1.14 g/cm³
    Viscosity (25 °C) 3600 mPa s

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Crack-bridging intermediate layer in the Remmers Deck OS 11a - II system
    • Crack-bridging wearing layer in the Remmers Deck OS 11b - II system
    • Crack-bridging intermediate layer in the Remmers Deck OS 14 system in accordance with the regulatory guideline on maintenance (2016 draft)

    Properties

    • Solvent-free
    • Highly elastic
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The tensile strength of the surface of the substrate must be at least 1.5 N/mm² on average (smallest individual value of at least 1.0 N/mm²), and the compressive strength must be at least 25 N/mm².

        Suitable substrates are surfaces prepared using Remmers Epoxy Primer PF in the Remmers Deck OS 11a - II and Deck OS 11b - II systems.

        Apply the crack-bridging layer no later than 24 hours after the primer.

    • Preparation
      • Mixing ratio comp. A 33.3 : comp. B 66.7
      • Mixing time 3 min
      • Combination container

        Stir component A thoroughly and add the full amount to hardener component B.

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Self-levelling coating / Apply standing
      • Pot life 30 min
      • Application temperature: min. 10 °C max. 30 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +10 °C to max. +30 °C.

      • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • Self-levelling coating / Apply standing
      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101 Thinner.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 9 months
      • If kept in the original container, unopened and protected against moisture and frost,
        component A will keep for at least 9 months and component B for at least 6 months.

    • Usage
      • See application examples

    • Application examples
      • Flow coating / blinding layer

        Once filler has been added in a ratio of up to 1 : 0.3 parts by weight, pour the material onto the prepared surface and spread using a suitable toothed trowel.

        Go over the material again with a spiked roller if necessary.

        Broadcast an excess of fire-dried quartz sand (grain size 0.3 - 0.8 mm) over the base layer while it is still wet.

        min. 2.1 kg/m² binder (OS 11b-II) and 0.63 kg/m² quartz sand (grain size 0.1 - 0.3 mm)

      • Coating

        Pour the material onto the prepared substrate and then distribute using a suitable tool, e.g. a notched trowel or notched scraper.

        Min. 1.7 kg/m² binder (OS 11a-II)

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

        Protect the coating against direct contact with water for the first 24 hours after application to prevent blistering.

        The additional material needed to attain the minimum layer thicknesses (wearing layer) and cover the surface texture must be calculated.

        Not suitable for recreation rooms.

        Abrasive mechanical loads leave traces of wear.

        Observe the instructions for use of the corresponding Remmers Deck OS 11 systems.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        Further information concerning safety during transport, storage and handling as well as on disposal and ecology can be found in the latest Safety Data Sheet.