• PUR RHE-217/10 Raw Wood Effect Lacquer
  • PUR RHE-217/10 Raw Wood Effect Lacquer
    • PUR RHE-217/10 Raw Wood Effect Lacquer
    • PUR RHE-217/10 Raw Wood Effect Lacquer

    Article No. 195720

    PUR RHE-217 Raw Wood Effect Varnish

    Two-component finish for natural wood effects on light and dark wood

    Colour: clear | 1957
    Size / Quantity

    Product specifications

    On delivery

    Binder Polyacrylate resin
    Density (20°C) Approx. 0.935 g/cm³
    Odour Characteristic
    Degree of gloss Cloth matt
    Runout time s (20° C, DIN 4) Approx. 20

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors
    • for furniture
    • For professional users only
    • Primer & top coat
    • Solid wood & veneers
    • High-quality furniture
    • Kitchen and bathroom furniture
    • Bleached wood
    • Wood for which emphasis of the grain is not desired


    • Solvent-based
    • Quick-drying
    • Excellent sanding properties
    • Good resistance to chemicals
    • Lightfast
    • No emphasis of the grain on the substrate
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood moisture content: 8-12%

      • Preparations

        Wash off greasy or resin-rich woods/substrates with WV-891 or V-890. Use UN-894 indoors on the construction site. Ensure good ventilation for solvents.

        Remove resin galls.

        Softwoods: sand with P 80 - 120.

        Hardwoods: sand with P 150 - 180.

        Coating should be carried out immediately after raw wood sanding.

        If colouring is desired, stain the substrate using Aqua KB-004, Aqua BB-007 or Aqua PB-006.

    • Application
      • Application temperature: min. 18 °C max. 25 °C
      • Airless/airmix spraying / Flow cup gun
      • Spray.

        Flow cup gun: nozzle size: 1.8 - 2.0 mm; atomiser air pressure: 2 - 3 bar.

        Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.

        Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.

        After drying and intermediate sanding if necessary (P 240 - 320), apply a second coat.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 1.5 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        The time period during which the product can be overcoated without the need for intermediate sanding is based on the information under "Overcoating" (drying time). Once this time period has been exceeded, the surface must be sanded and dusted off immediately prior to further coats.

        Use breathable materials when packing the coated wood building elements.

      • Drying

        Dust-dry: after approx. 15 minutes
        Overcoating: after approx. 1.5 hours (the best raw wood effect is achieved when left to dry overnight)

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

        If the humidity level is high during drying, clouding may occur.

      • Thinning

        If necessary with V 890 Thinner or V 899 Thinner.

    • Working tools / cleaning
      • Airless/airmix spraying / Flow cup gun
      • Airless/airmix spraying equipment, flow cup gun

      • Airless/airmix spraying equipment, flow cup gun

        Clean tools using WV-891 Brush Wash or V-890 Thinner.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 24 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

    • Usage
      • Approx. 80 ml - 120 ml / m² per layer applied
      • 80 - 120 ml/m² per coat

    • General information
      • To preserve the quality of the surface, we recommend regular cleaning and care using a lint-free cotton cloth. Please use solvent-free and silicone-free cleaning agents.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.