• PUR FG-201 Filling Primer
  • PUR FG-201 Filling Primer
    • PUR FG-201 Filling Primer
    • PUR FG-201 Filling Primer

    Article No. 195005

    PUR FG-201 Filling Primer

    Light-fast, two-component filling primer for semi-closed to closed-pore lacquering systems

    Colour: clear | 1950
    Size / Quantity

    Product specifications

    On delivery

    Density (20°C) Approx. 0.95 g/cm³
    Odour Characteristic
    Runout time s (20° C, DIN 4) Approx. 27

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors
    • for furniture
    • For professional users only
    • Solid wood & veneers
    • Bleached wood
    • Wood materials
    • High-quality furniture
    • Kitchen and bathroom furniture

    Properties

    • Solvent-based
    • Very fast drying
    • Good sanding properties
    • Good build on the surface
    • Lightfast
    • Free of aromatic compounds
    • Fire behaviour according to DIN EN 13501-1: C-s2,d0 on suitable substrates
    • Suitable for interior finishing of ships (IMO)
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood moisture content: 8-12%

      • Preparations

        Wash off greasy or resin-rich woods/substrates with WV-891 or V-890. Use UN-894 indoors on the construction site. Ensure good ventilation for solvents.

        Remove resin galls.

        Softwoods: sand with P 80 - 120.

        All other substrates: sand with P 180 - 320.

        Coating should be carried out immediately after sanding the bare wood.

        If colouring is desired, stain the substrate using Aqua KB-004, Aqua BB-007 or Aqua PB-006.

    • Application
      • Application temperature: min. 18 °C max. 25 °C
      • Airless/airmix spraying / Flow cup gun
      • Spray.

        Flow cup gun: nozzle size: 1.8 - 2.0 mm; atomiser air pressure: 2 - 3 bar.

        Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.

        Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.

        After drying and intermediate sanding if necessary (P 240 - 320), apply a second coat.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 1.5 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Before coating technically modified woods and wood-based materials, apply the product to a trial surface and conduct a suitability test on the desired area of use.

        The time period during which the product can be overcoated without the need for intermediate sanding is based on the information under "Overcoating" (drying time). Once this time period has been exceeded, the surface must be sanded and dusted off immediately prior to further coats.

      • Drying

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        As needed

    • Working tools / cleaning
      • Airless/airmix spraying / Flow cup gun
      • Airless/airmix spraying equipment, flow cup gun

        Clean tools using WV-891 Brush Wash or V-890 Thinner.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 24 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

    • Usage
      • Approx. 80 ml - 120 ml / m² per layer applied
      • 80 - 120 ml/m² per coat

    • General information
      • Please refer to the relevant test reports/certificates and the Technical Data Sheet for information on certified products and configurations.

        For applications in accordance with the Marine Equipment Directive, the maximum wet application quantity is 3 x 120 g/m².

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.