• PUR Aqua ​Top M
  • PUR Aqua ​Top M
  • PUR Aqua ​Top M
    • PUR Aqua ​Top M
    • PUR Aqua ​Top M
    • PUR Aqua ​Top M

    Article No. 367306

    PUR Aqua
    Top M

    Aqueous, transparent, two-component sealant

    3673 | PUR Aqua ​Top M
    Size / Quantity

    Product specifications

    On delivery

    Solids content 52%

    Component A

    Density (20°C) 1.00 g/cm³

    Component B

    Density (20°C) 1.06 g/cm³


    Density (20°C) 1.06 g/cm³

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Sealant in decorative EP and PU coating systems


    • Matt surface
    • Hard-wearing
    • Low-maintenance
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The substrate must be prepared using suitable Remmers products.

      • Preparations

        Apply the sealant within 48 hours. In the case of longer waiting times, sand the surface treated in the previous coat and remove dust.

        When using QP products, apply the sealant within 12 hours.

    • Preparation
      • Mixing ratio comp. A 90 : comp. B 10
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the base compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

        If the compound is not properly mixed, formation of specks may occur. In such cases, the material must be strained (1000 µ lacquer strainer).

    • Application
      • Application temperature: min. 10 °C max. 25 °C
      • By roller
      • Pot life 45 min
      • Application requirements

        Temperature of the material, air and substrate: from min. +10 °C to max. +25 °C

      • Higher temperatures and higher absolute humidity reduce the specified times, while lower temperatures and lower absolute humidity increase them.

    • Working tools / cleaning
      • By roller
      • Epoxy roller, mixing apparatus

      • More detailed information can be found in the Remmers Tool Programme.

        Wash tools and any splashed material with water immediately and while wet.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 6 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 6 months.

    • Usage
      • Min. 0.12 kg/m²

    • Application examples
      • Sealant

        Pour the material onto the surface and spread evenly crosswise using a suitable 25 cm epoxy roller. Replace the roller every 30 minutes.

        Always work wet-on-wet.

        min. 0.12 kg/m²

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C). Slight deviations from these values may arise if the product is worked with on site.

        Use sufficiently experienced personnel to ensure that surfaces are as even as possible.

        If the processing time is exceeded, roller marks or differences in degree of gloss and colour may occur.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.

        Uneven application and large temperature differences on the surface may lead to a non-uniform surface appearance due to differences in the degree of gloss.

        Abrasive mechanical loads leave traces of wear.

        Not suitable for areas subjected to vehicle loads or dynamic point loads.

        Coloured rubber – in particular black rubber – may leave discolouration upon contact with a floor covering that cannot be removed (e.g. car tyres or machine feet). Suitable polyurethane wheels and/or mats should be used in order to avoid such discolouration. Pigments, hair dyes, bleach and disinfectants can also cause discolouration if not removed immediately.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        Further information concerning safety during transport, storage and handling as well as on disposal and ecology can be found in the latest Safety Data Sheet.