• Epoxy WHG Color AS
  • Epoxy WHG Color AS
  • Epoxy WHG Color AS
    • Epoxy WHG Color AS
    • Epoxy WHG Color AS
    • Epoxy WHG Color AS

    Article No. 143111

    Epoxy WHG Color AS

    Dissipative, chemically resistant, crack-bridging coating

    Colour:
    pebble grey (approx. RAL 7032) | 1431
    Colour: pebble grey (approx. RAL 7032) | 1431
    Please choose a colour
    Size / Quantity

    Product specifications

    On delivery

    Component A

    Density (20°C) 1.70 g/cm³
    Viscosity (25 °C) 4500 mPa s

    Component B

    Density (20°C) 1.06 g/cm³
    Viscosity (25 °C) 450 mPa s

    Mixture

    Density (20°C) 1.50 g/cm³
    Viscosity (25 °C) 2000 mPa s
    Slip resistance class
    (DIN EN 51130:2014)
    R10 (degree of blinding 20% Mica GHL 3/0) R12 (blinding with SIC 04)

    Once fully cured

    Once fully cured

    Flexural tensile strength Approx. 17 N/mm² *
    Compressive strength Approx. 45 N/mm² *
    Shore D after 28 days 59

    * Epoxy resin mortar 1 : 10 with standard sand ** Fire test class in defined systems (see test report on fire classification: Remmers dissipative systems)

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Conductive, chemically resistant, crack-bridging coating
    • Coating in the system SL Floor WHG AS (AbZ Z-59.12-303)

    Properties

    • Conductive
    • With static crack-bridging ability
    • Highly resistant to chemicals
    • Fire resistant
    • Suitable for hand pallet trucks and forklift trucks
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The adhesive pull strength of the surface after priming must be at least 1.5 N/mm² on average (smallest single value min. 1.0 N/mm²), compressive strength at least 25 N/mm².

        Suitable Remmers epoxy primers, epoxy scratch coats or epoxy mortars must always be used.

        For works within the framework of the general building inspectorate approval, the substrates must correspond to the requirements of the approval and the system products mentioned therein must be used.

      • Preparations

        Before the application of the product a smooth surface must be produced, e.g. with a scratch coat.

        Refer to the current Technical Data Sheet for detailed information on the single products.

        Epoxy Conductive must be applied according to the current Technical Data Sheet as transverse conducting layer.

    • Preparation
      • Mixing ratio comp. A 100 : comp. B 20
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the base compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Application temperature: min. 10 °C max. 30 °C
      • Self-levelling coating / Apply standing
      • Pot life 45 min
      • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • Self-levelling coating / Apply standing
      • Toothed trowel, notched spreader, spiked roller (metal), rubber scraper, epoxy roller, suitable mixing apparatus

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • See application examples

    • Application examples
      • Coating

        Pour the material onto the prepared substrate and then distribute using a suitable tool, e.g. a notched trowel or notched scraper.

        Afterwards roll over with a (metal) spiked roller.

        min. 1.5 kg/m² binder

      • Base layer for blinded coatings

        Pour the unfilled material on the previously prepared surface, distribute with a suitable toothed trowel/squeegee and, if required, roll over with a spiked roller.

        Broadcast an excess of suitable silicon carbide or Ceramix Conduct 04/08 into the wet base layer.

        Remove any loose, excess material after hardening.

        min. 0.8 kg/m² binder and
        5 - 6 kg/m² silicon carbide or Ceramix Conduct 04/08 (including excess)

      • Top sealant

        Pour the material onto the prepared surface, spread evenly using a rubber scraper, then roll crossways using a suitable epoxy roller.

        approx. 0.6 - 0.7 kg/m² binder

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

        The stated approximate application quantities refer to smooth, level substrates.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        Carbon fibres are visible on the surface. Because of the way the coating is applied, the carbon fibres may bundle.

        Due to the black transverse conducting layer, poorly covering colours are not to be used.

        When used as a top seal, the inherent colour of the granules may limit the opacity of light shades.

        Before the application of the covering layer, the correct functioning of the transverse conducting layer and of the connections must be proved and registered in a measurement report.

        The use of the product as a blinding layer or top seal does not form part of the AbZ certification (Z-59.12-303).

        Low levels of air humidity can cause a higher discharge resistance, uneven or thicker layers can even lead the coating to not be conductive at all.

        Application of the mixture by toothed trowel/toothed spreader. If the product is applied with a smoothing trowel/screed levelling tool, trowel marks may be visible on the finished surface.

        In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.

        Abrasive mechanical loads leave traces of wear.

        Exposure to vehicles with metal or polyamide tyres as well as dynamic concentrated loads can cause faster wearing of the coating.

        Epoxy resins are generally not colourfast when exposed to UV light or weather.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet and the brochure entitled "Epoxy Resins in the Construction Industry and the Environment", issued by Deutsche Bauchemie e.V. (3rd edition 2022).