• Epoxy Color Top
  • Epoxy Color Top
    • Epoxy Color Top
    • Epoxy Color Top

    Article No. 619311

    Epoxy Color Top

    Pigmented roll-on coating or topcoat

    Colour:
    pebble grey (approx. RAL 7032) | 6193
    Colour: pebble grey (approx. RAL 7032) | 6193
    Please choose a colour
    Size / Quantity

    Product specifications

    On delivery

    Component A

    Density (20°C) 1.66 g/cm³
    Viscosity (25 °C) 4000 mPa·s

    Component B

    Density (20°C) 1.05 g/cm³
    Viscosity (25 °C) 90 mPa·s

    Mixture

    Density (20°C) 1.51 g/cm³
    Viscosity (25 °C) 1050 mPa·s

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Topcoat in the Remmers Deck OS 8 and Deck OS 8 classic systems
    • Topcoat in the Remmers Deck OS 11a-II and OS 11b-II systems
    • Topcoat in the Remmers Deck OS 14 system in accordance with the maintenance guideline (draft 2016)
    • Top sealant for blinded covers
    • Coloured coating for roller application

    Properties

    • Excellent protection against carbamate formation
    • Good hiding power on blinded coatings
    • Can be subjected to mechanical loads
    • Can be subjected to chemical loads
    • Coating compatibility test
    • Contains no plasticisers, nonylphenols or alkylphenols
    • Physiologically harmless once fully cured
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        It is imperative to use suitable Remmers Epoxy Primers and coating systems.

        Remmers Epoxy and Polyurethane Base Coatings fully sprinkled with quartz sand are also suitable as substrates.

        For the Remmers Deck OS systems, see the applicable instructions for use.

    • Preparation
      • Mixing ratio comp. A 82 : comp. B 18
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the base compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Application temperature: min. 10 °C max. 25 °C
      • Pot life 25 min
      • Setting may be accelerated by adding ACC H. The associated directions for use are available upon request.

        As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • By brush / By roller
      • Rubber wiper, epoxy roller, mixer

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 12 months
      • If stored unopened in the original container and kept cool, dry and protected from frost, min. 12 months (component A)/min. 24 months (component B).

    • Usage
      • See application examples

    • Application examples
      • Top sealant

        Apply the material using a rubber wiper and then roll cross-wise with a suitable epoxy roller.

        approx. 0.5 - 0.8 kg/m² binder (depending on blinding)

      • Roller coating

        Pour the material onto the prepared substrate and then distribute using a suitable tool, e.g. a notched trowel or notched scraper.

        Then roll in a crosswise direction using a suitable epoxy roller.

        approx. 0.35 kg/m²

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

        Where necessary, the viscosity can be reduced by adding up to 2% by mass of Remmers V101 Thinner. The use of other thinning agents is not recommended.

        Shades of colour with low hiding power (e.g. yellow, red or orange) tend to have a translucent effect on the subsequently applied sealant. In such cases, it is necessary to build up a coordinated colour, e.g. with multiple layers of sealant.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        If dark or highly pigmented colours are used it is possible that, even with very careful application, shadows or light textures appear on the surface. This is due to the product system and does not in any way affect product suitability. In case of doubt set up a trial surface.

        Suitable for vehicle traffic with rubber tyres; not suitable for vehicle loads with metal or polyamide tyres nor for dynamic point loads.

        Abrasive mechanical loads leave traces of wear.

        Epoxy resins are generally not colourfast when exposed to UV light or weather.

        Observe the corresponding test certificate for OS 8 systems.

        Observe the instructions for use of the corresponding Remmers Deck OS 11 systems.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet and the brochure entitled "Epoxy Resins in the Construction Industry and the Environment", issued by Deutsche Bauchemie e.V. (3rd edition 2022).