Article No. 683826

    Epoxy SIC Color ESD

    ESD hard grain coating

    Colour: special colours from 100 kg | 6838
    Size / Quantity

    Product specifications

    On delivery

    Component A

    Density (20°C) 1.70 g/cm³
    Viscosity (25 °C) thixotropic

    Component B

    Density (20°C) 1.05 g/cm³
    Viscosity (25 °C) 130 mPa s

    Mixture

    Density (20°C) 1.56 g/cm³
    Viscosity (25 °C) thixotropic
    Slip resistance class
    (DIN EN 51130:2014)
    R10

    * Fire test class in defined systems (see test report on fire classification: Remmers conductive systems)

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Textured hard grain coating for e.g. ESD protection zones

    Properties

    • Slip-resistant
    • Dissipative / ESD-compliant
    • Volume conductive when used in a system
    • Free from solid salts and aqueous salt solutions
    • Coating compatibility test
    • Resistant to wear
    • Can be subjected to mechanical loads
    • Can be subjected to chemical loads
    • Physiologically harmless once fully cured
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        Suitable Remmers epoxy primers, epoxy scratch coats or epoxy mortars must always be used.

      • Preparations

        Before the application of the product a smooth surface must be produced, e.g. with a scratch coat.

        Install earthing elements and copper strands prior to application, based on the size and shape of the surface. Make sure that no point on the surface is more than 10 m from an earthing point or a connected copper strand.

        Refer to the current Technical Data Sheet for detailed information on the single products.

    • Preparation
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the base compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • Smoothing trowel
      • Pot life 30 min
      • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • Smoothing trowel
      • Smoothing trowel, suitable textured roller, suitable mixer

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 12 months
      • If stored unopened in the original container and kept cool, dry and protected from frost, min. 12 months (component A)/min. 24 months (component B).

    • Usage
      • Approx. 0.6 kg/m² binder

    • Application examples
      • Textured coating

        Use a smoothing trowel, or an angled scraper for upright application, to spread the material evenly over the grain.

        Uneven application can lead to visible texture differences.

        After applying, intensively re-roll the fresh material with a textured roller at right angles to the direction of application. To reduce roller marks etc., re-roll in one direction without pressure using a 50 cm textured roller, for example.

        approx. 0.6 kg/m² binder

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        Colours with low hiding power (e.g. yellow, red or orange) tend to act as a translucent coating, meaning that a primer of the same colour must be used.

        Low levels of air humidity can cause a higher discharge resistance, uneven or thicker layers can even lead the coating to not be conductive at all.

        Before checking the ESD values, we recommend cleaning the ESD shoes, the electrodes and the floor coating with isopropyl alcohol or ethanol (95%) and waiting until it has evaporated.

        The resulting surface texture is heavily dependent on the conditions on the building site, as well as the working procedure used. It is therefore not covered under product liability.

        Low thickness and low temperature can affect the visual effect of the finished surface.

        Depending on the application and system, pores may be created due to air pockets when texturing the thixotropic coating material. These may accumulate dirt during use.

        Abrasive mechanical loads leave traces of wear.

        Suitable for vehicle traffic with rubber tyres; not suitable for vehicle loads with metal or polyamide tyres nor for dynamic point loads.

        Epoxy resins are generally not colourfast when exposed to UV light or weather.

        In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.

        Anti-slip floors naturally require more cleaning effort than smooth surfaces. Therefore, the use of cleaning machines with soft brushes is recommended.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet and the brochure entitled "Epoxy Resins in the Construction Industry and the Environment", issued by Deutsche Bauchemie e.V. (3rd edition 2022).