Epoxy ZE Color AS

The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

The adhesive pull strength of the surface after priming must be at least 1.5 N/mm² on average (smallest single value min. 1.0 N/mm²), compressive strength at least 25 N/mm².

A suitable Remmers epoxy primer or epoxy scratch coat must always be used.

Refer to the current Technical Data Sheet for detailed information on the single products.

Always apply Epoxy Conductive LE as a transverse conductive layer in accordance with the current Technical Data Sheet.

Add the entire quantity of the hardener (component B) to the base compound (component A).

Mix thoroughly with a slow-speed electric mixer
(approx. 300 - 400 rpm).

Pour the mixture into a separate container and mix again thoroughly.

Mix for at least 3 minutes.

Insufficient mixing is indicated by streaks forming.

Setting may be accelerated by adding ACC H. The associated directions for use are available upon request.

As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

Toothed trowel, notched scraper, loop roller, spiked roller, suitable mixing equipment

More detailed information can be found in the Remmers Tool Programme.

Clean tools, equipment and splashed material immediately while fresh with V 101.

Take suitable protective and waste disposal measures when cleaning.

If stored unopened in the original container and kept cool, dry and protected from frost, min. 12 months (component A)/min. 24 months (component B).

The stated approximate application quantities refer to smooth, level substrates.

Pour the material onto the prepared substrate and then distribute using a suitable tool, e.g. a notched trowel or notched scraper.

Subsequently roll over with a looped or a spiked roller.

The application rate depends on the substrate, temperature, required coating thickness, and optical requirements.

approx. 1.8 - 2.5 kg/m² binder

Apply the material to the prepared surface, spread with a suitable toothed trowel/notched scraper and, if necessary, finish with a spiked roller.

Scatter an excess of Ceramix Conduct 04/08 onto the base coat while it is still wet.

Remove any loose, excess material after hardening.

approx. 1.4 kg/m² binder and
5 - 6 kg/m² Ceramix Conduct 04/08

Pour the material onto the prepared surface, spread evenly using a rubber scraper, then roll crossways using a suitable epoxy roller.

approx. 0.6 – 0.7 kg/m² binder

Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

From experience, slightly opaque colours (e.g. yellow, red or orange, etc.) have a varnishing effect. Please consider this when choosing and assembling systems.

Due to the black transverse conducting layer, poorly covering colours are not to be used.

When used as a top seal, the inherent colour of the granules may limit the opacity of light shades.

When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

Application of the mixture by toothed trowel/toothed spreader. If the product is applied with a smoothing trowel/screed levelling tool, trowel marks may be visible on the finished surface.

In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.

Abrasive mechanical loads leave traces of wear.

The conductivity of the coating is due to its carbon fibres. These are only slightly visible in highly opaque and darker colours. Colours with low opacity should not be used on account of the visibility of the carbon fibres and the potential for the black transverse conducting layer to show through.

Before the application of the covering layer, the correct functioning of the transverse conducting layer and of the connections must be proved and registered in a measurement report.

Exposure to vehicles with metal or polyamide tyres as well as dynamic concentrated loads can cause faster wearing of the coating.

Epoxy resins are generally not colourfast when exposed to UV light or weather.

Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.