• Epoxy UV 100 New
  • Epoxy UV 100 New
  • Epoxy UV 100 New
  • Epoxy UV 100 New
  • Epoxy UV 100 New
  • Epoxy UV 100 New
    • Epoxy UV 100 New
    • Epoxy UV 100 New
    • Epoxy UV 100 New
    • Epoxy UV 100 New
    • Epoxy UV 100 New
    • Epoxy UV 100 New

    Article No. 634403

    Epoxy UV 100

    Transparent epoxy resin with a low tendency to yellow

    Product specifications

    On delivery

    Component A

    Density (20°C) 1.12 g/cm³
    Viscosity (25 °C) 750 mPa s

    Component B

    Density (20°C) 1.01 g/cm³
    Viscosity (25 °C) 450 mPa s

    Mixture

    Density (20°C) 1.08 g/cm³
    Viscosity (25 °C) 615 mPa s

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • Binder for decorative pebble covers
    • Topcoat for blinded covers
    • Fixative coat for flake coatings that completly saturate the surface
    • Transparent coating
    • System component in TÜV PROFICERT-product Interior certified systems (707106482-1)

    Properties

    • Resistant to yellowing
    • Can be subjected to mechanical loads
    • Contains no plasticisers, nonylphenols or alkylphenols
    • Preparation
      • Substrate requirements

        The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

        The tensile strength of the surface of the substrate must be at least 1.5 N/mm² on average (smallest individual value of at least 1.0 N/mm²), and the compressive strength must be at least 25 N/mm².

        A suitable Remmers epoxy primer or epoxy scratch coat must always be used.

        Refer to the current Technical Data Sheet for detailed information on the single products.

    • Preparation
      • Mixing ratio comp. A 66.6 : comp. B 33.4
      • Mixing time 3 min
      • Combination container

        Add the entire quantity of the hardener (component B) to the base compound (component A).

        Mix thoroughly with a slow-speed electric mixer
        (approx. 300 - 400 rpm).

        Pour the mixture into a separate container and mix again thoroughly.

        Mix for at least 3 minutes.

        Insufficient mixing is indicated by streaks forming.

    • Application
      • By brush / By roller / Self-levelling coating / Apply standing
      • Pot life 30 min
      • Application temperature: min. 12 °C max. 30 °C
      • Application requirements

        Temperature of material, surroundings and substrate: min +12 °C to max. +30 °C

      • As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

    • Working tools / cleaning
      • By brush / By roller / Self-levelling coating / Apply standing
      • Smoothing trowel, toothed trowel, rubber squeegee, epoxy roller, mixing equipment, if necessary a positive mixer

      • More detailed information can be found in the Remmers Tool Programme.

        Clean tools, equipment and splashed material immediately while fresh with V 101 Thinner.

        Take suitable protective and waste disposal measures when cleaning.

    • Storage / shelf life
      • Store frost-free
      • Shelf-life 12 months
      • If stored unopened in the original container and kept cool, dry and protected from frost, min. 12 months (component A)/min. 24 months (component B).

    • Usage
      • See application examples

    • Application examples
      • Head seal

        Pour the material on the previously prepared surface and distribute with a suitable rubber squeegee or smoothing trowel and then roll over crosswise with an epoxy roller.

        approx. 0.5 - 0.7 kg/m² of binder (depending on the blinding material used)

      • Fixation for flakes

        Pour the material on the previously prepared surface and distribute with a suitable rubber squeegee or smoothing trowel and then roll over crosswise with an epoxy roller.

        To obtain a smooth surface apply the material several times. After complete curing, apply the sealant.

        approx. 0.3 kg/m² of binder (depending on the blinding material used)

      • Epoxy mortar

        Pour the material which has been filled up to 1:12.5 parts by weight onto the primed surface and distribute, compact and level with a smoothing trowel

        Per mm thick layer: approx. 0.16 kg/m² of binder and 2.0 kg/m² of Ceramix 20/30

      • Transparent coating

        Pour the material on the suitable and previously prepared surface and distribute with suitable means, such as a toothed squeegee/trowel.

        Afterwards roll over with a (metal) spiked roller.

        When completely cured, seal e.g. with PUR Top M Plus.

        Alternative substrates or system elements must be tested with regard to their suitability.

        approx. 1.5 kg/m² of binder

    • General information
      • Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C). Slight deviations from these values may arise if the product is worked with on site.

        When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

        Exposure to vehicles with metal or polyamide tyres as well as dynamic concentrated loads can cause faster wearing of the coating.

        Abrasive mechanical loads leave traces of wear.

        Low temperatures during application can reduce the resistance to water. If the surfaces are exposed to water, executed the coating only at air and substrate temperatures of over 12 °C.

        Epoxy resins are generally not colourfast when exposed to UV light or weather.

        UV resistance can be improved with a suitable sealant.

        Not suitable for application in outdoor areas.

        Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For professional users only!

        For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet and the brochure entitled "Epoxy Resins in the Construction Industry and the Environment", issued by Deutsche Bauchemie e.V. (2nd edition 2009).

    Accessories