Article No. 195805
Two-component spray filler/sealing filler for opaque surfaces
Product specifications
On delivery
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- Preparing opaque, pigmented varnishes
- High-quality furniture
- Solid wood and wood-based materials
- Pigment filler on insulated surfaces
- As a sealing filler (5:1 with PUR H-280)
Properties
- Good sanding properties
- High stability
- Excellent filling and hiding power
- Good sealing effect
- Light-fast with PUR H-280
- Good resistance to climatic changes
- Fire resistant
-
Preparation
-
Substrate requirements
The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.
Wood moisture content: 8-12%
-
Preparations
Wash off greasy or resin-rich woods/substrates with WV-891 or V-890. Use UN-894 indoors on the construction site. Ensure good ventilation for solvents.
Remove resin galls.
Sand panels using P 180 - 320 grit.
Sand wood using P 100 - 180 grit.
-
-
Application
-
Application requirements
Temperature of the material, air and substrate: from min. +18°C to max. +25°C.
-
Stir well.
Spray.
Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.
Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.
Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.
Once dry, carry out intermediate sanding with P 240-320.
Repeat the process if necessary.
Intermediate and final coats of suitable products can be applied after drying.
Seal opened containers well and use contents as soon as possible.
-
-
Application instructions
-
Check colour, adhesion and compatibility with the substrate by setting up a trial area.
Before coating technically modified woods and wood-based materials, apply the coating to a trial surface and conduct a suitability test on the desired area of use.
The time period during which the product can be overcoated without the need for intermediate sanding is based on the information under "Overcoating" (drying time). Once this time period has been exceeded, the surface must be sanded and dusted off immediately prior to further coats.
Use breathable materials when packing the coated wood building elements.
-
Drying
Mixing ratio 10:1 with PUR H-280
Dust dry: after approx. 10 minutes
Ready for overcoating: after approx. 2 hours
Mixing ratio 10:1 with PUR H-286
Dust dry: after approx. 10 minutes
Ready for overcoating: after approx. 1 hour
Mixing ratio 5:1 with PUR H-280
Dust dry: after approx. 45 minutes
Ready for overcoating: after approx. 6 hoursPractice values at +20 °C and 65% relative humidity.
Low temperatures, poor ventilation and high humidity delay drying.
-
-
Working tools / cleaning
-
Airless/airmix spraying equipment, flow cup gun
-
Clean tools using WV-891 Brush Wash or V-890 Thinner.
Ensure that any residue from cleaning is disposed of correctly.
-
-
Storage / shelf life
-
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.
-
-
Usage
-
120 - 150 ml/m² per coat
-
-
General information
-
Please refer to the relevant test reports/certificates and the Technical Data Sheet for information on certified products and configurations.
-
-
Disposal instructions
-
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
-
-
Safety / regulations
-
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.
-
