Article No. 124520
Abrasion-resistant, single-component finish
Product specifications
On delivery
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- Interior wood
- Primer & top coat
- Solid wood & veneers
- Wooden stairs
- Living room & bedroom furniture
- Interior finishing work: e.g. panels, borders, cladding & interior doors
Properties
- Quick-drying and easy to sand
- Can also be used on vertical surfaces
- Resistant to abrasion and scratches
- Resistant to chemicals: DIN 68861, 1C
- Good resistance to a wide range of commercially available hand creams
- 2K-Ready: further, isocyanate-free increase of chemical, hand cream & abrasion resistance by addition of 2% Aqua VGA-485
-
Preparation
-
Substrate requirements
The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.
Wood moisture content: 8-12%
-
Preparations
Wash off greasy or resin-rich woods/substrates with WV-891 or V-890. Use UN-894 indoors on the construction site. Ensure good ventilation for solvents.
Sand wood using P 100 - 180 grit.
If colouring is desired, stain the substrate using Aqua KB-004, Aqua BB-007 or Aqua PB-006.
-
-
Application
-
Stir well.
Apply with a brush, roller or by spraying.
Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.
Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.
Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.
After drying and intermediate sanding (P 240 - 320), apply a second and third coat of the product.
Seal opened containers well and use contents as soon as possible.
-
-
Application instructions
-
Check colour, adhesion and compatibility with the substrate by setting up a trial area.
Before coating technically modified woods and wood-based materials, apply the coating to a trial surface and conduct a suitability test on the desired area of use.
-
Drying
Dust-dry: after approx. 60 minutes
Touch-dry: after approx. 2 hours
Overcoating: after approx. 4 hours
Stacking: after drying overnightPractice values at +20 °C and 65% relative humidity.
Low temperatures, poor ventilation and high humidity delay drying.
-
Thinning
Ready to use; dilute with max. 5% water if necessary.
-
-
Working tools / cleaning
-
Airless/Airmix spraying equipment, flow cup gun, sealant roller with microfibre cover (pile height 8 mm), acrylic brush
-
Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.
Ensure that any residue from cleaning is disposed of correctly.
-
-
Storage / shelf life
-
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.
-
-
Usage
-
100 - 120 ml/m² per coat
-
-
General information
-
Observe the "Care instructions for sealed flooring and stairs".
-
-
Disposal instructions
-
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
-
-
Safety / regulations
-
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.
-
