• Colour Opaque 2in1
    • Colour Opaque 2in1

    Article No. 131783

    Colour Opaque 2 in 1

    Primer and finish with corrosion protection: direct application onto iron, steel & wood

    Colour: flame red (RAL 3000) | 1317
    Colour: flame red (RAL 3000) | 1317
    Please choose a colour
    Size / Quantity

    Discontinued product This container size is being phased out and is only available to a limited extent.

    View the new product

    Product specifications

    On delivery

    Density (20°C) 1.0 - 1.3 g/cm³
    Flash point > 60 °C
    Odour Characteristic
    Degree of gloss High gloss
    Viscosity Approx. 900 - 2500 mPa∙s

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for dimensionally stable elements
    • Interior and exterior use
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Direct application onto sound and lightly rusted ferrous metals
    • Radiators

    Properties

    • Solvent-based
    • Primer and finishing coat all in one
    • High total solids level for greater covering capacity
    • Good flow properties
    • Resistant to shocks and scratches
    • Weather-resistant and UV-resistant
    • Resistant to extreme temperatures and little tendency to yellow
    • Protects against corrosion
    • Preparation
      • Substrate requirements

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Exterior wood that needs to be protected against soft rot and blue stain must be pre-treated with a suitable wood preservative* (*Use biocides safely. Always read the label and product information before use).

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

        Thoroughly sand any old coatings that are still intact.

        Iron, steel:

        Derust thoroughly. Remove scale layers and rolling skin (derust manually to SA 3 standard of cleanliness). The best results are achieved if the substrate has been sand blasted to SA 2.5 standard of cleanliness (DIN EN ISO 12944-4).

    • Application
      • Application temperature: min. 5 °C max. 25 °C
      • Stir before use
      • By brush / By roller / Airless/airmix spraying
      • Stir well.

        Apply with a brush, roller or by spraying.

        Apply further coats once dry.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 24 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Areas that are being coated or dried should be protected against rain, wind, sunlight and condensation.

        On surfaces that are not exposed to daylight, e.g. the inner surfaces of windows and external doors, alkyd resin systems exhibit a certain degree of dark yellowing, in particular in rebates.

        Bright, intense colours such as yellow, orange and red may have a lower covering capacity as a natural consequence of the pigments used. When using these colours, it is therefore recommended either to first apply a coat of a similar colour with a greater covering capacity, or to apply a second coat in the desired colour.

        Take appropriate measures to protect adjacent building elements and materials that should not come into contact with the product.

      • Drying

        After approx. 24 hours at 20 °C and 65% relative humidity.

        The coating may take significantly longer to dry thoroughly in lower temperatures, at high humidity or if the maximum layer thickness has been exceeded.

      • Thinning

        Ready to use

    • Working tools / cleaning
      • By brush / By roller / Airless/airmix spraying
      • Brush, roller, flow cup gun or airless spraying equipment

      • Clean tools immediately after use with thinner and brush cleaner.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 24 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

        Use the contents of open containers as quickly as possible.

    • Usage
      • Approx. 60 ml - 80 ml / m² per layer applied
      • Min. 2 x 60 - 80 ml/m² per coat
        Dry film thickness: approx. 40 - 50 µm

    • General information
      • On planed larch and softwoods with a high resin content, the coating may have reduced adhesion and resistance to weathering. This is especially the case on horizontal year rings, knots and areas of winter growth that are high in resin. Maintenance and renovation must be carried out more frequently on these surfaces.
        The only remedy for this is pre-weathering or very coarse sanding (P80).
        If these wood types are rough-sawn, considerably longer maintenance and renovation intervals are to be expected.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.