• Acryl 100
    • Acryl 100

    Article No. 736012

    Acryl 100

    Premium acrylic sealant, fast-acting rainproof effect

    Colour: grey | 7360
    Colour: grey | 7360
    Please choose a colour

    Product specifications

    On delivery

    Skin formation Approx. 15 min. (+23°C/50% RH)
    Viscosity Paste-like/stable
    (DIN EN ISO 1183-1A)
    1.6 g/cm³

    Once fully cured

    Once fully cured

    100% (DIN EN ISO 8339)
    0.06 N/mm²
    Elongation at break
    (DIN EN ISO 8339)
    Volume loss
    (DIN EN ISO 10563)
    < 20%
    Permissible total deformation
    (DIN EN 15651-1)

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for dimensionally stable elements
    • Waterproofing dimensionally stable building elements
    • Sealing cracks
    • Repairing facades, masonry, render and wood surfaces
    • Materials with low strength, e.g. aerated concrete and gypsum building materials
    • Wood/wooden joints, especially in log cabin construction


    • Can be overcoated
    • Fast-acting rainproof effect
    • Elastoplastic
    • Solvent-free
    • Preparation
      • Substrate requirements

        The substrate must be dry to slightly damp, clean and free of grease, and capable of supporting a load. Metals must be bare.

      • Preparations

        Underpin joint widths ≥ 1 cm with a round cord.

        Prime highly absorbent joint edges (Acryl 100 1:1 in water).

    • Application
      • Application temperature: min. 5 °C max. 30 °C
      • Sealant gun / Filling knife
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +30 °C

      • Cut off tip at an angle according to the width of the joint and inject, filling the joint completely.

        Application depth of the material: 75% of the joint width.

        Apply the material with sufficient pressure to the sides of the joint, then smoothen with a moist spatula.

    • Application instructions
      • Hardening times increase at increasing joint depths.

        A coating can be applied as soon as the surface can no longer be damaged.

    • Working tools / cleaning
      • Sealant gun / Filling knife
      • Hand-held and compressed-air applicators, scraper, adhesive tape

      • Manual and compressed air gun, scraper, adhesive tape

        Wash the material off with soapy water while wet.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • At least 36 months in unopened, original containers stored cool, dry and protected from frost.

    • Usage
      • Total application rate approx. 100 ml / cm² x m
      • Approx. 100 ml/m for a 1 cm² joint cross-section

    • General information
      • Protect from water and sunlight until the material has hardened sufficiently.

        Deviations from applicable regulations must be agreed separately.

        Observe the instructions of IVD Leaflet No. 20 from the German Sealants Industry Association IVD.

        The relevant test certificates must be observed when planning and carrying out work.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.